Awol A1-ACI00 Ultra Short Throw Projector
About Screen
How it works
There is an Absorbent Layer and Reflective Layer in the AWOL ALR Cinematic Screens serriform op:ical surface lens microstructure, (shown above the Cescrictive dia;arn)_ The Absorbent Layer captures up to 95% of light from overneat sources. Ambien: light reflecting from the screen’ssurfacee is directed dowrjwæd towæd the Absorbent Layer 10 to avoid washing out the protected image. The Reflective Leyer diverts the projector’s light ttothe viewer’s line of vision.
Exploded Overview
Package Contents
- Inner Frames *4
- Inner Frames *2
- Phillips-Head Screwdriver*2
- Support Rod *1
- M4*8 Screws *16
- Gloves *2 (pairs)
- ALR Screen *1
- Fiberglass *6 Strips
- Springs *NÂ Draw
- Hooks *2
- Exterior Frames *4 • Exterior Frames *2
- Corner *4 Protectors
- Wall Drilling *1 Templates
- Wall Anchors ® with Screws *8 (sets)
- Level *1 Ruler
- Â Upper WallBrackets *2
- Lower Wall Brackets *2
- User Manual *1
- Adhesive Tapes *4
Assembly
Inner Frames
- Connect the horizontal frames and fasten the MfiA7 screws.
- Insert the four corner oonnæntors into the horizontal inner frames, and attach the corners with V? 7 screws as shown
- Install the support rod as shown below
Screen
- Put on ‘gloves and place a Dluan Cloth (IN use through packaging material for the surface), an Ilat, Clean and levesurfacejz.
- Unroll the screen, place it face •down on the cloth, then insert the fiberglass strips intothee screen sides. Caution• Handle with care. Avoid any creases on the screen.
- Put the assembled frames on the back side of the screen.
- Fix the screen onto the frame with all the springs in order as indicated below (corners, short sides, then long sides).
- Hold the screen upright and ensure that it is taut and flat. Adjust the springs until no creases are observed.
Outer Frames
- Place the outer frames against the inner frames, align the four corners, and attach with the included M4*8 screws. Attach the plastic corner protectors to the four corners.
Mount on the Wall
- Estimate the wall mount area for the screen.
- The height between the ground and the lower edge of the screen should be confirmed by your preferred UST projector throw distance using the throw distance chart.
- Measure the distance between the spots where the wall brackets will be mounted with the included level ruler.
Recommended Distance
- Make sure the screen is correctly assernt•lecd, then wrap the screen front with the cloth to prevent it from being damaged or scratched.
Screen Height Adjustment
You can fine-tune the installation height of the screen without drilling new holes based on the screw holes in the upper wall bracket and the lower wall bracket spring range. ( Adjustable height range: 0-2.0 inches)
Maintenance
Dust, dirt, and scratches on the projection screen surface will | affect the quality and performance of the projection image. For optimal results, we advise paying attention to the following instructions.
- The screen surface has a horizontal structure.
- DO NOT wipe the screen up and down or in a circular motion. Wipe from left to right only.
- Gently wipe the screen with a moistened microfiber cloth with mild soap diluted in water.
- The following precautions should be followed at all times to avoid damaging the material, which is not covered under warranty.
- Don’t touch the screen material to avoid leaving fingerprints.
- Usegloves when handling the material.
- Don’t scratch the material, as it will leave permanent markings on the screen’s surface.
- Don’t use acetone, benzene, alcoholorrd any other organic solvents to clean the screen material.
- Using such chemicals will permanently damage the screen.
Specification
Customer Service
- Tel:Â +1 (888) 891-6866
- Customer Service Hours: Monday–Friday, 9 AM–6 PM
- Website:Â https://awolvision.com/