Honeywell CS071AE Portable Evaporative Air Cooler
PARTS DESCRIPTION
- Control Panel
- Louvers
- Water Level Indicator
- Casters
- Water Fill Door
- Drain Plug
- Side Grill
- Honeycomb Cooling Media
- Power Cord & Plug
USE & OPERATION
CONTROL PANEL
Icons on Control Panel
- Power
- Cool
- Speed
- Low
- Medium
- High
- Swing
FUNCTION BUTTONS
POWER
Press the button to turn the unit on. The cooler will start automatically at medium speed. After a few seconds, the speed will switch to low. To turn the unit off, press the button again.
COOL
You must add water before operating the unit in Cool mode. Press the button untiit l is illuminated on the display screen. The water pump will operate, and you will feel the cooler air after the Honeycomb Cooling Media is completely wet.
SPEED
Press the SPEED button repeatedly to change the speed between | – || – |||.
SWING
Press the SWING button until it’s illuminated on the display. The louvers will begin to move left to right automatically. You can manually adjust the louvers to change vertical air flow.
REMOTE CONTROL
- POWER: ON / OFF
- SPEED: Low / Medium / High
- COOL: Evaporative Cooling ON / OFF
- SWING: Controls the motion of the louvers
NOTE
- The remote control requires a CR2025 (1 x 3V) coin-type or equivalent battery for replacement. Open the battery compartment at the back of the remote control and insert the battery inside. Do not drop the remote control.
- Do not mix different types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
- Do not mix old and new batteries.
- Do not recharge the battery.
WARNING: Chemical Burn Hazard. Keep batteries away from children.
COOLER LOCATION
Make sure to position the air cooler correctly before you set up and start using the product. Please refer to the COOLER LOCATION section of the separate Safety & Maintenance Guide.
FILLING WITH WATER
CAUTION: Unplug the unit from the electrical socket before emptying or refilling the water tank.
Open the Water Fill Door located on the back of the unit.
Manual Tank Refilling
The Water Level Indicator is located at the front of the unit. Refill the water tank when the water level is low. Do not fill water above the “Max.” water level mark to avoid water droplets collecting on the louvers.
Check the water level in the tank before running the COOL function. Make sure that the water in the tank is above the minimum water level mark. Running the unit in COOL mode with inadequate water may cause pump failure.
LOW WATER ALARM
The unit is equipped with a low water sensor. In Cooling Mode, when water in the tank is below the minimum level, you will hear a beeping sound and the GREEN LED will flash continuously. The unit will automatically pause evaporative cooling.
Refill the water tank to deactivate the alarm in cooling mode. First, switch OFF the unit and unplug it from the power outlet. Fill the water tank with water above the minimum water level mark. Plug in and switch ON again.
To deactivate the alarm and continue using the unit as a fan (without evaporative cooling), switch the unit OFF and then ON again. The Low Water Alarm will not activate in Fan-only mode. The Low Water Alarm will sound again if the COOL function is activated while the water tank is still empty.
CLEANING & DRAINING THE WATER TANK
Below are instructions on how to clean and maintain your air cooler. If the cooler will not be used for a long period, please refer to the STORAGE & MAINTENANCE GUIDELINES located in the separate Safety & Maintenance Guide.
WARNING
Before cleaning the unit, power OFF the unit and disconnect it from the electrical socket.
- Move the unit to a location where the water Honeywell CS071AE Portable Evaporative Air Cooler can be drained. Remove the cap from the drain plug located at the bottom of the unit. Allow the tank to empty.
- Refill the water tank with clean water, up to the maximum level, and drain it completely.
- Use a damp cloth to remove the dirt and dust from the surface of the unit. Never use corrosive elements or chemicals to clean this product.
- When the product is not in use, store the unit in a dry place out of direct sunlight.
CLEANING THE HONEYCOMB COOLING MEDIA
WARNING
Before cleaning the unit, switch the unit OFF and disconnect the power adapter from the unit and the electrical socket.
- The appliance is supplied with a Honeycomb Cooling Media.
- The Honeycomb Cooling Media are located inside the Side Grill. See Figure 1 for instructions on how to remove them from the unit for cleaning and maintenance.
- Do not run the unit in COOL mode with stale water in the tank. You must empty the water tank and refill it with fresh water, especially if the tank has not been cleaned in a long time.
Removing the Honeycomb Cooling Media
- Remove all the screws from the side grill of the Air Cooler, and carefully pull out the side grill from the cooler.
- Rinse the side grill with clean water and let it dry before reinstalling it onto the unit.
- Carefully pull out the Honeycomb Media from the unit.
- Replace or clean media with water and a damp cloth as needed.
WARNING
DO NOT operate the Air Cooler when the side Grill Honeywell CS071AE Portable Evaporative Air Cooler is removed from the Air Cooler, or if there is a loose-fitting side Grill. Doing so can cause serious injury or dangerous electrical shock.
Customer Service
Website:
