Honeywell RDWL311A2000 Wireless Doorbell User Manual

Honeywell RDWL311A2000 Wireless Doorbell

Safety Instructions

Before proceeding with the installation, please note the following safety warnings.

• Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.,g. safety goggles) when drilling holes, etc.
• Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt.

Install Batteries

1. Open the battery cover and install 4 AA alkaline batteries.
2. Open the battery cover and install the CR2032 battery.

Overview

Just follow these simple steps

1. Install batteries.
2. Set up the doorbell and your preferences.
3. Install the doorbell and the push button.

Setup and Operation

Press the push button to test whether it is paired with the doorbell. The doorbell will ring.

Change the Tune

Press the Music button to change the doorbell tune. Every time you press the Music button, the tune will change. Stop pressing the Music button when you hear the tune you want.

Ding Dong Westminster Soft Alert Smart Sax

Installation

Choose a location that is not near a heat source or on something that moves (like a door). For non-mounting locations, choose a place where the doorbell will be easy to hear.

Install Doorbell

If you are not mounting the doorbell to the wall, place it where you want it.

1. Mount the scronto to the wall using the supplied anchor if necessary.
2. Leave 2 mm of the screw sticking out from the wall. Drill 1/4 inch (6.3 mm) holes for the anchor.
3. Hang the doorbell on the screw.

Install Push Button

1. Mount the push button bracket in the desired location.
2. Use the screws –OR– Use the adhesive backing. If using the adhesive backing, clean the surface first.
3. Snap the push button onto the mounting bracket.

Note

If you need to remove the push button, use a small screwdriver to release the tab.

Accessories

You can connect 2 accessories to your doorbell, including other push buttons, window or door opening sensors, and motion sensors.

• If you try to connect more accessories than the maximum number, the LED on the side blinks red.

Connect a Motion Sensor

1. Press and hold the Setting button on the doorbell for three seconds. The LED on the side turns on with an amber color.
2. Within 20 seconds of pressing the Setting button, wave or make some other kind of motion in front of the motion sensor.

Connect a Push Button

Follow these steps to change the ring for an existing doorbell, too.

1. Press and hold the Setting button on the doorbell for three seconds. The LED on the side turns on with an amber color.
2. Press the push button.
3. Within 12 seconds of pressing the push button, press the Music button to select the ring for that push button.

Secret Knock

You can set up a Secret Knock that makes a different ring for each push button. The Secret Knock is triggered by pressing the push button quickly 3 times.

1. Press the push button 3 times quickly.
2. Within 12 seconds of pressing the push button, press the Music button to select the ring for the Secret Knock.

Preparation

In the box you will find

To install, you will need

• Phillips Screwdriver
• Standard Screwdriver
• Drill and 1/4 in. (6.3 mm) drill bit

• 4 AA alkaline batteries

The push button supplied with this kit is pre-programmed to operate with the doorbell.

Specifications

Maintenance

Your doorbell and push button require no maintenance except to periodically change the batteries.

If using the correct batteries, battery life should be approximately:

• Up to 2 years for the doorbell; replace with 4 AA alkaline batteries
• Up to 2 years for the push button; replace with a CR2032 lithium battery

Low Battery Notification

When the doorbell batteries are low, the LED on the side turns on.  When the push button batteries are low, two beeps are heard after the normal tune.

Reset

This process removes all pairings, including the push button that came with this doorbell:

1. Remove the doorbell battery.
2. Press and hold the Setting button, and replace the battery at the same time.
3. The doorbell will beep several times rapidly and return to its factory default settings.

Troubleshooting

FCC Regulations

This device complies with part 15 of the FCC Rules. Honeywell RDWL311A2000 Wireless Doorbell Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and usedbyh the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  This equipment should be installed and operated with a minimum distance of 20 millimeters between the radiator and your body.

IC Regulations

This device complies with Industry Canada Honeywell RDWL311A2000 Wireless Doorbell licence‐exempt RSS standard(s). Operation is subject to the following two conditions

• Users can obtain Canadian information on RF exposure and compliance.
• The operation of this equipment is subject to the following two conditions:
• This equipment or device may not cause harmful interference, and
• This equipment or device must accept any interference, including interference that may cause undesired operation.

Warranty

• 1-year limited warranty Resideo warrants this product, excluding battery, to be free from defects in workmanship or materials, under normal use and service, for one (1) year from the date of first purchase by the original purchaser.
• Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
• Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
• This warranty provides you with specific legal rights, and you may have other rights that vary from state to state. If you have any questions Honeywell RDWL311A2000 Wireless Doorbell concerning this warranty, please write.
• Printed in the United States.

© 2020 Resideo Technologies, Inc. All rights reserved.

Customer Support

• Website:  resideo.com
• Tell: 1-800-633-3991.

FAQs

Q: How can I connect the doorbell and push button?
Ans: To pair the doorbell, press and hold the Setting button on the receiver’s top or side for approximately three seconds, or until the side LED glows amber. Make a single push-button press. For pairing to be confirmed, the receiver must chime.

Q: How can I add more sensors or push buttons?
Ans: The RDWL311A2000 has the capacity to hold several transmitters, such as extra doorbell buttons and accessories that work with Honeywell Home.

Q: How can I alter the LED light pattern and chime sound?
Ans: Press and hold the Setting button until the amber LED appears to enter the chime/light setting. To switch between the available light patterns, Honeywell RDWL311A2000 Wireless Doorbell and tones, press the push button.

Q: How can I silence the doorbell or change the volume?
Ans: To adjust the volume settings, press the receiver’s Volume button. To enable or disable the temporary mute/Do Not Disturb feature found in many Series 3 units, press and hold the Volume (or Mute) control as directed in your handbook.

Q: The doorbell is not ringing when I press my push button. What am I supposed to check?
Ans: Battery: Verify that the CR2032 in the push button is new and polarity-correctly inserted. Distance/obstruction: To rule out interference or range, test the button that is closer to the receiver.