Makita JV001G Cordless Jig Saw
Safety Instructions
- Use clamps or another practical way to secure and support the workpiece to a stable platform.
- Holding the workpiece by hand or against your body leaves it unstable and may lead to loss of control.
- Always use safety glasses or goggles. Ordinary eye or sunglasses are NOT safety glasses.
- Avoid cutting nails. Inspect the workpiece for any nails and remove them before the operation.
- Make sure the jig saw blade is not contacting the workpiece before the switch is turned on.
- Keep your hands away from moving parts.
- Do not leave the tool running. Operate the tool only when hand-held.
- Do not operate the tool at no-load unnecessarily.
- Some material contains chemicals that may be toxic.
- Always use the correct dust mask/respirator for the material and application you are working with.
Battery Cartridge
- Do not disassemble or tamper with the battery cartridge.
- It may result in a fire, excessive heat, or explosion.
- If operating time has become excessively shorter, stop operating immediately.
- It may result in a risk of overheating, possible burns, and even an explosion.
- Do not touch the terminals with any conductive material.
- Avoid storing the battery cartridge in a container with other metal objects such as nails, coins, etc.
- Do not expose the battery cartridge to water or rain.
- Do not touch the terminal of the tool immediately after use, as it may get hot enough to cause burns.
- Keep the battery away from children.
The Makita JV001G cordless jig saw uses a standard Makita lithium-ion battery, compatible with other Makita tools. For more heavy-duty options, see the Makita TW011G Cordless Impact Wrench Guide.
Intended Use
The tool is intended for the sawing of wood, plastic, and metal materials.
Noise
The typical A-weighted noise level determined according to EN62841-2-11:
- Sound pressure level (Lp): 87 dB (A)
- Sound power level (LWA: 98 dB (A)
- Uncertainty (K) : 3 dB (A)
Vibration
The vibration total value (tri-axial vector sum) is determined according to EN62841-2-11:
- Work mode: cutting boards
- Vibration emission (ah, B: 4.6 m/s2
- Uncertainty (K): 2.5 m/s2
- Work mode: cutting sheet metal
- Vibration emission (ah, M ): 4.8 m/s2
- Uncertainty (K)Â 1.5 m/s
Functional Description
Installing or removing a battery cartridge
To remove the battery cartridge, slide it from the tool while pressing the button on the front of the cartridge. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator as shown in the figure, it is not locked completely.
Indicating the Remaining Battery Capacity
Press the check button on the battery cartridge to indicate the remaining battery capacity. The indicator lamps light up for a few seconds.
Indicator lamps. Check button
Tool/battery Protection System
The tool is equipped with a tool/battery protection system. This system automatically cuts off power to the motor to extend tool and battery life. The tool will automatically stop during operation if the tool or battery is placed under one of the following conditions:
Overload Protection
When the battery is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops without any indication. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart.
Overheat Protection
When the tool or battery is overheated, the tool stops automatically, and the lamp blinks. In this case, let the tool and battery cool before turning the tool on again.
Overdischarge Protection
When the battery capacity is not enough, the tool stops automatically. In this case, remove the battery from the tool and charge the battery.
- Turn the tool off, and then turn it on again to restart.
- Charge the battery(ies) or replace it/them with a recharged battery(ies).
- Let the tool and battery(ies) cool down.
If no improvement can be found by restoring the protection system, then contact your local Makita Service Center.
Selecting the Cutting Action
This tool can be operated with an orbital or a straight line (up and down) cutting action. The orbital cutting action thrusts the jig saw blade forward and increases cutting speed.
Cutting action changing lever
To change the cutting action, turn the cutting action changing lever to the desired cutting action position. Refer to the table to select the appropriate cutting action. 
Lighting Up the Front Lamp
Press the lock switch to turn on the lamp. Press the lock switch again to turn off the lamp.
Lock switch. Lamp
Switch Action
To turn on the tool, press the lock switch. The tool turns into the standby mode. To start the tool, press the ON/ standby switch in the standby mode. To stop the tool, press the ON/standby switch again. The tool turns into the standby mode. To turn off the tool, press the lock switch in the standby mode.
Lock switch. ON/standby switch
To decrease the brightness of the lamp, press and hold the lock switch when turning it into the standby mode. About 1 second after you start pressing the lock switch, the brightness of the lamp will start to decrease, so release the lock switch when you reach the desired brightness. It turns the tool into standby mode, too. About 3 seconds after you start pressing the lock switch, the brightness of the lamp will be minimized, and the brightness will not change after that.
Speed Adjusting Dial
The tool speed can be adjusted by turning the speed adjusting dial. You can get the highest speed at 6 and the lowest speed at 1. Refer to the table to select the proper speed for the workpiece to be cut. However, the appropriate speed may differ with the type or thickness of the workpiece. In general, higher speeds will allow you to cut workpieces faster, but the service life of the jig saw blade will be reduced.
- Electronic function
The tool is equipped with electronic functions for easy operation. - Soft start
The soft-start function minimizes start-up shock and makes the tool start smoothly. - Constant speed control
Electronic speed control for obtaining a constant speed. Possible to get a fine finish, because the rotating speed is kept constant even under load conditions. - Soft no-load rotation
Once the tool starts cutting the workpiece, the tool speed increases and reaches the preset speed.
Disabling or Enabling the Soft Rotation Function
To disable or enable the soft no-load rotation function, follow the steps below.
- Make sure that the tool is turned off.
- Set the speed adjusting dial to “1”.
- Press the lock switch to turn on the tool.
- Turn the speed adjusting dial to “6”, and then set it back to “1”.
The lamp blinks twice when the soft no-load rotation function is disabled or enabled. To enable or disable this function again, perform the same procedure.
Assembly
Installing or removing a jigsaw blade.
Before installing the jig saw blade, make sure that the jig saw blade clamp lever is in the released position. To install the jig saw blade, insert the jig saw blade (teeth facing forward) into the jig saw blade holder until it latches. The jig saw blade clamp lever moves to the fixed position by itself, and the jig saw blade is locked. Make sure that the back edge of the jig saw blade fits into the roller. Pull the jig saw blade lightly to make sure that the jig saw blade does not fall off during operation.
1. Jig saw blade clamp lever (fixed position) 2. Jig saw blade clamp lever (released position)
1. Jigsaw blade holder 2. Jig saw blade clamp lever (released position) 3. Jigsaw blade 4. Roller
To remove the jig saw blade, open the tool opener forward as far as it will go. This allows the jigsaw blade to be released.
Customer Support
Website:Â