Seeed Studio J401 ReComputer Carrier Board User Guide

Seeed Studio J401 ReComputer Carrier Board

Intended use

The Seeed Studio J401 ReComputer Carrier Board is intended for indoor use only. Do not use it outdoors, and avoid any contact with moisture under all circumstances. Using the J401 ReComputer Carrier Board for purposes other than those described may damage the product. Improper use can result in short circuits, fires, electric shocks, or other hazards. The product complies with statutory national and European requirements.

For safety and approval purposes, you must not rebuild or modify the Seeed Studio J401 ReComputer Carrier Board. Read the safety instructions and any accompanying instructions carefully and store them in a safe place. Make this product available to third parties only together with the safety instructions and accompanying instructions.

Safety Instructions

Before using the Seeed Studio J401 ReComputer Carrier Board, read this document and the accompanying operating instructions carefully, and especially observe the safety information. If you do not follow the safety instructions and information on proper handling, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

• The J401 ReComputer Carrier Board is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly.
• This may become dangerous playing material for children.
• If you have questions that remain unanswered by this information product, contact our technical support service or other technical personnel.
• Handle the product carefully. Jolts, impact, or a fall, even from a low height, can damage the product
• Do not place the product under any mechanical stress.
• Protect the appliance from extreme temperatures, strong jolts, flammable gases, steam, and solvents.
• Protect the product from high humidity and moisture.
• Protect the product from direct sunlight.

Operation

• Consult an expert when in doubt about the operation, safety, or connection of the
  product.
• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. DO NOT attempt to repair the product yourself.

Power Adapter

Do not modify or repair mains supply components, including mains plugs, mains cables, and power supplies. Do not use damaged components. Risk of death by electric shock!

• Connect the appliance to a wall socket that can be accessed easily.
• Only connect the power adaptor to a normal mains socket connected to the public supply. Before plugging in the power adaptor, check whether the voltage stated on the power adaptor complies with the voltage of your electricity supplier.
• Never connect or disconnect power adaptors if your hands are wet.
• Never unplug the power adaptor from the mains socket by pulling on the cable; always use the grips on the plug.
• For safety reasons, disconnect the power adaptor from the mains socket during storms.
• Do not touch the power adapter if there are any signs of damage, as this may cause a
  fatal electric shock! Take the following steps:
• Switch off the mains voltage to the socket containing the power adapter (switch off the corresponding circuit breaker or remove the safety fuse, and then switch off the corresponding RCD protective switch).
• Unplug the power adapter from the mains socket.
• Use a new power adapter of the same design. Do not use the damaged adapter again.
• Ensure that cables are not pinched, kinked, or damaged by sharp edges.
• Always lay cables so that nobody can trip over or become entangled in them. This poses a risk of injury.

Connected devices

• Also, observe the safety and operating instructions of any other devices that are connected to the product.

Disposal

This symbol must appear on any electrical and electronic equipment placed on the EU market. This symbol indicates that this device should not be disposed of as unsorted municipal waste at the end of its service life. Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose of it separately from unsorted municipal waste. Spent batteries and accumulators, which are not enclosed by the WEEE, as well as lamps that can be removed from the WEEE in a non-destructive manner, must be removed by end users from the WEEE in a non-destructive manner before it is handed over to a collection point. Distributors of electrical and electronic equipment are legally obliged to provide free takeback of waste. Conrad provides the following return options free of charge (more details on our website):

• In our Conrad offices
• at the Conrad collection point
• at the collection points of public waste management authorities or the collection points set up by manufacturers or distributors within the meaning of the Elektrororo G, End users are responsible for deleting personal data from the WEEE to be disposed of. It should be noted that different obligations about the return or recycling of WEEE may apply in countries outside of Germany.

Technical data

Power supply

• Input: 9 – 19 V/DC

PoadapterterP

• Input :100 – 240 V/AC
• Output:12 V/DC, 5 A;
• Barrel Jack: 5.5/2.5 mm;
• Inside (+) / Outside (-)

Environment

• Usage environment indoor
• Operating temperature:-10 to +60 °C
• Operating humidity: max. 95 % RH (non-condensing) (at 40 °C)
• Storage temperature :. -40 to +85 °C
• Storage humidity: <80 % RH (non-condensing)

Others

• Dimensions (L x W) (approx.): 100 x 80 mm
• Weight (approx.):0.2 kg

Customer Support

• Website: www.seeedstudio.com
• Ph: +86-0755-86095676

2008-2025 Seeed Technology Co., Ltd. All rights reserved.