VacMaster CA0701UK EasyClean Home Carpet Cleaner
Safety Instructions
- Do not leave the appliance when plugged in.
- Unplug from the outlet when not in use and before servicing.
- Not for space heating purposes.
- Make sure the household voltage is the same as that indicated on the rating label of the unit.
- Always switch off, unplug from the socket after use or before cleaning the appliance or any maintenance task.
- Do not unplug by pulling and jerking the cord with force.
- Do not handle the plug or the appliance with wet hands.
- Do not use the appliance in any outdoor area. Commercial use will void the warranty.
- Do not step on or wrap the cord around arms or legs when using the appliance.
- Do not pull, lift, or carry the appliance by its supply cord.
- In order to avoid damage to the cord, do not pull the cord around sharp corners and edges.
- Keep the appliance away from the ovens and stoves, etc.
Installation
- Remove the floor nozzle cover by gripping the two nozzle cover release tabs and pulling up. Remove the floor nozzle cover by gripping the two nozzle cover release tabs and pulling up.
- Use the nozzle cleaning tool to remove any dirt and debris from the slot openings of the nozzle cover. If required, rinse the nozzle cover and allow it to air dry
- Use the nozzle cleaning tool to remove VacMaster CA0701UK EasyClean Home Carpet Cleaner any build-up tangled around the brushrolls.
- Reinstall the nozzle cover. Lock the two tabs on the nozzle cover into the slots on the front edge of the floor nozzle.
- Lock the nozzle cover into place by rotating it down until a click is heard.~
Troubleshooting
Should you have any problem(s) with your steam mop, review the table below for solutions to minor performance issues.
| PROBLEM | POSSIBLE CAUSE | SOLUTION |
| The steam mop will not power on (the indicator light will not illuminate). | The plug is not plugged into the wall outlet. | Be sure the power cord plug is fully plugged into the outlet. |
| Defective power cord. | Check the power cord condition; if there is any damage, contact customer service. | |
| Blown fuse or breaker. | Replace the fuse or reset the breaker in the home. | |
| The internal fuse is blown. | Contact with customer service. | |
| The indicator light illuminates red. | The water tank may be empty. | Fill up the water tank with water. |
| Reduced steam or no steam. | The water tank may be empty. | Fill up the water tank with water. |
| There is no power to the steam mop. | Make sure the steam mop is plugged into a good wall outlet. | |
Customer Support
- Website: www.vacmasterfresh.com/product-registration/
- Visit: vacmasterfresh.com/contact-us/
- Tel: 1-866-384-8432.
FAQs
What is the VacMaster CA0701UK designed for?
Using a water-and-solution cleaning method, it efficiently gets rid of spills, pet stains, pollutants, and smells.
Can I use the CA0701UK on hard floors?
Other versions, such as the EasyClean Floor Cleaner, are available from VacMaster for hard floor cleaning.
Does it heat the water during cleaning?
No, a built-in water heater is not a feature of the CA0701UK. Use warm tap water in the clean water tank (no more than 60°C/140°F) for best results.
What kind of cleaning solution should I use?
Only use carpet cleaning solutions designed for extraction cleaners that are low-foam. Avoid using high-foam detergents, bleach, or strong chemicals as these can harm internal parts and void the warranty.
How long does the carpet take to dry after cleaning?
Although drying times vary depending on factors including humidity, ventilation, and carpet thickness, most carpets dry in two to six hours. To expedite the process, increase airflow with fans or open windows.
Can the brush roller be removed for cleaning?
Yes, you can wash and remove the brush roller. To avoid dirt, hair, and carpet fibre accumulation that could impair cleaning effectiveness, clean it frequently.