Meec Tools 024232 Saw Blades Grinding Machine
Safety Instructions
- Keep the work area clean and well-lit.
- Dark and cluttered work areas increase the risk of accidents and injuries.
- Power tools produce sparks that can ignite dust and fumes.
- Keep children and onlookers at a safe distance when using power tools.
- You can easily lose control of the tool if you are distracted.
- The plug on the power tool must match the power outlet.
- Never modify the plug in any way. Never use an adapter with earthed power tools.
- Unmodified plugs and matching outlets reduce the risk of electric shock.
- Avoid body contact with earthed surfaces such as pipes, radiators, cookers and refrigerators.
- There is an increased risk of electric shock if your body is earthed.
- Do not expose power tools to rain or moisture.
- There is a greater risk of electric shock if water gets into a power tool.
- Keep the power cord away from heat, oil, sharp edges and moving parts.
- Damaged or tangled power cords increase the risk of electric shock
- Only use an extension cord approved for outdoor use.
- Cords intended for outdoor use reduce the risk of electric shock.
- Remove Allen keys/spanners, etc., before starting the power tool.
- Allen keys, or the like, left in a rotating part of a power tool can cause personal injury.
- Do not overreach. Always maintain a firm footing and good balance.
- This will ensure you have better control over the tool in unexpected situations.
- Wear suitable clothing. Do not wear loose-fitting clothing or jewellery.
- Keep your hair, clothing and gloves away from moving parts.
Description
The product is intended to be used for sharpening circular saw blades with a diameter of up to 400 mm.
- Motor
- Blade holder
- Support for the saw blade
- Handle
- Power switch
- Base plate
Assembly
Remove the lock nut, washers, spring and centring piece from the blade holder. Put the blade to be sharpened on the screw and replace the parts as shown in the drawing.
- Lock nut
- Washer
- Spring
- Washer
- Centring piece
- Saw blade
The saw blade must be centred, but not locked. Do not tighten the lock nut so hard that the saw blade cannot rotate. Check that the centring piece is not at an angle.
Using the Device
Switch off the product, pull out the plug and Meec Tools 024232 Saw Blades Grinding Machine wait until all moving parts have completely stopped before cleaning, adjusting, maintenance and/or replacing accessories.
Adjusting the Blade
Adjust the position of the saw blade about the grindstone, as shown in the figures below, to sharpen the front and back of the tooth.
- Back of the tooth
- Front of the tooth
- Bottom of the tooth
Positioning of the grindstone when sharpening the front of the tooth.
Positioning of the grindstone when sharpening Meec Tools 024232 Saw Blades Grinding Mac, grinding the back of the tooth.
- Adjust the arm of the blade holder and, if necessary, the position of the motor, depending on the diameter of the saw blade.
- Undo the lock nut and pull out (2) and turn (1) the arm.
- Adjust the saw blade to the correct position on the grindstone. Lift the handle to adjust and align the grindstone to the bottom of the tooth.
Examples For Adjustment
- Saw blade 90 mm: Motor moved back.
- Saw blade 230 mm: Motor moved forward to avoid collision with the arm.
- Saw blade 400 mm: Motor moved forward, arm turned away so that the lock nut does not collide with the saw blade.
Depth Stop
Tighten the lock screw to lock the depth stop in place.
Support for the Saw Blade
For better stability and alignment, the support for the blade should be placed as close to the grindstone as possible so that the blade is resting against it.
Sharpening of the set saw bla.de
The motor can be angled to sharpen the teeth on the blade to the required angle. Undo the lock nuts on each side of the motor and adjust to the required angle. The motor can be angled up to about 25° both ways.
The motor can go against the base plate when adjusting larger angles. In which case, undo the clamping screw on the motor bracket, turn the motor 180° and tighten the screw.
Sharpening a circular saw blade
Start the product and use the handle to move the grindstone against the tooth until it reaches the set depth. Pull back the grindstone with the handle, turn the saw blade and sharpen the next tooth. To sharpen the back of the teeth, adjust the grindstone according to the instructions.
MAINTENANCE
Switch off the product, pull out the plug and wait until all moving parts have completely stopped before cleaning, adjusting, maintenance and/or replacing accessories. Keep the product clean and dry. Clean the product with a dry or damp cloth. Lubricate moving parts at regular intervals. Do not use strong or flammable detergents. The motor is maintenance-free. Keep the ventilation openings on the product clean to avoid overheating.
Technical Data
- Rated voltage 230 VAC, 50 Hz
- Rated output 110 W
- Speed, no load 5700 rpm
- Diameter, grindstone 100 mm
- Saw blade diameter 90–400 mm
- Weight 5.4 kg
- Sound pressure level, LpA: 69.0 dB(A), K= 3 dB
- Sound power level, LwA: 82 dB(A), K= 3 dB
Limited Warranty
Normal Wear: Many power tools need periodic parts replacement and service to achieve the best performance. This warranty does not cover repair when normal use has exhausted the life of a part, including, but not limited to, chucks, brushes, cords, saw shoes, blade clamps, o-rings, seals, bumpers, driver blades, pistons, strikers, lifters, and bumper cover.
Customer Support
- Website: https://www.jula.se/varumarken/meec-tools/
- Tel: +39-0645652462
FAQs
Q: What is the Meec Tools 024232?
Circular saw blades and other compatible cutting tools can be sharpened with the Meec Tools 024232 saw blade grinding machine, which guarantees accurate and uniform edges for metalworking and woodworking.
Q: What is the maximum blade diameter supported?
The device can accommodate blades with a diameter of up to 300 mm, or around 12 inches. Larger blades might not rotate correctly or fit snugly.
Q: Is the machine safe for continuous use?
Yes, however, to avoid overheating and wear, let the motor and grinding wheel cool after prolonged usage.
Q: Is dust collection necessary?
Indeed. Fine metal and carbide dust are produced during grinding. Use in an area with good ventilation or connect an appropriate dust extractor.
Q: Can I grind other cutting tools?
Yes, as long as the wheel is appropriate for the material and the tool fits the clamp. Prior to grinding non-standard tools, consult the manual’s instructions.
Q: Can I use the machine outdoors?
No. To avoid electrical dangers and grinding wheel contamination, operate the grinding machine in a dry, stable indoor environment.