Ronix RP-4100 Multi Functional Cleaning Equipment User Manual

Ronix RP-4100 Multi-Functional Cleaning Equipment

Safety Instructions

Please read and comply with these original instructions prior to the initial operation of your appliance and store them for later use or subsequent owners. Apart from the notes contained herein, the general safety provisions and rules for the prevention of accidents of the legislator must be observed. Warnings and notes that are attached to the appliance provide important notes for safe operation.

Electric Components

Never touch the mains plug and the socket with wet hands. Check the power cord with the mains plug for damage before every use. Do not use the machine if a supply cord or important parts of the machine are damaged, e.g., safety devices, high-pressure hoses, or the trigger gun. All current-conducting parts in the working area must be protected against jet water.

The mains plug and the coupling of an extension cable must be watertight and must never lie in water. Moreover, the coupling may never lie on the ground. The use of cable reels that ensure that the sockets are at least 60 mm above the ground is commended.

Make sure that the power cord or extension cable is not damaged by running over, pinching, dragging, or the like. Protect the power cords from heat, oil, and sharp edges. Always switch off the mains disconnecting switch when leaving the appliance unattended.

Safe Handling

The user must be the appliance as intended. The person must consider the local conditions and must pay attention to other persons in the vicinity when working with the appliance. Check important components, such as high-pressure hose, hand spray gun, and safety installations, for damage before every operation. Immediately replace damaged components. Do not operate the appliance with damaged components.

The appliance has been designed for use with the cleaning agent supplied or recommended by the manufacturer. The use of other cleaning agents or chemicals may adversely affect the safety of the appliance. High-pressure jets can be dangerous if subject to misuse. The jet must not be directed at persons, live electrical equipment, or the machine itself.

Do not direct the jet against yourself or others in order to clean clothes or footwear. Do not use the appliance within the range of persons unless they wear protective clothing. Wear appropriate Personal Protective Equipment (PPE) while operating the appliance. Do not direct the jet against yourself or others in order to clean clothes or footwear.

Other Risks

The appliance may not be operating in explosive atmospheres. Risk of explosion – Do not spray flammable liquids. Never draw in fluids containing solvents or undiluted acids and solvents!

This includes petrol, paint thinner, and heating oil. The spray mist is highly inflammable, explosive, and poisonous. Do not use acetone, undiluted acids, or solvents, as they corrode the materials used on the appliance. Never use the product with inflammable or toxic liquids, or liquids with characteristics incompatible with its proper operation. Keep packaging films away from children, as there is a risk of suffocation!

Mind the weight of the appliance when selecting the storage location and during transport to prevent accidents or injuries. Several hours of continuous use of the appliance can lead to numbness in the hands in rare cases.

• Wear gloves.
• Keep your hands warm.
• Take breaks at regular intervals. Working with detergent

Residual Risk

Even if you are operating this product in accordance with all the safety requirements, potential risks of injury and damage remain. The following dangers can arise in connection with the structure and design of this product:

Health defects resulting from vibration emission may occur if the product is being used over long periods of time or is not adequately managed and properly maintained. Danger of injury and property damage caused by flying objects. Injuries and damage to property due to broken accessories or the sudden impact of hidden objects during use.

Safety Devices

• Safety installations serve the protection of the user and may not be modified in the past.

Power Switch

• The appliance switch prevents unintentional operation of the appliance.

Lock Trigger Gun

• This lock locks the lever of the trigger gun and prevents the inadvertent start of the appliance. Overflow valve with. Water that has flowed through backflow preventers is considered to be non-potable.

Pressure Switch

• If the lever on the trigger gun is released, the pressure switch turns off the pump, and the high-pressure jet is stopped. If the lever is pulled, the pump is turned on again.

Motor Protection

• The motor protection switches off the device if the power consumption is high.

Personal Protective Equipment

Wear protective clothing and safety goggles to protect against splashback containing water or dirt. During the use of a high-pressure cleaner’s aerosols can develop. Inhaling aerosols can cause health damage.

• Depending on the application, completely shielded nozzles (e.g., surface cleaners)that significantly reduce the emission of aqueous aerosols can be used for high-pressure cleaning.
• The use of such shielding is not possible with all applications.

Spcifications

Part List

Proper Use

Use this pressure washer for private households only: If a connection is made to a potable water system, the system shall be protected against backflow. This high-pressure cleaner is designated with a rated input current. The intended use of this product covers the cleaning of vehicles, buildings, terraces, facades, and garden equipment using clean water and biodegradable chemical detergents. Likewise, the product can be used to clean paving slabs or rain gutters.

This product may not be used to clean clothing, shoes, and other textiles. The water jet should not be directed against persons. Animals, any electrical equipment, or the product itself. Do not flush any objects that contain hazardous materials. The product must not be run with inflammable, explosive, or toxic liquids. For safety reasons, it is essential to read the entire instruction manual before the first operation and to observe all the instructions therein.

If you are looking for another similar model, you can also check the complete manual for the Ronix RP-1160 High Pressure Washer.

Assembly

Mount the loose parts delivered with the appliance before start-up

1. INSTALLING THE HANDLE WITH A SCREW
2. SLIDE THE TRIGGER GUN HOOK INTO POSITION
3. INSTALLING THE DUST COMPARTMENT INTO POSITION
4. INSTALLING THE SPRAY WAND TO TRIGGER
   GUN: Fit the spray wand into the gun and rotate it until the two parts are completely locked.
5. CONNECT THE HIGH-PRESSURE HOSE TO THE TRIGGER GUN
   Connect the silver end of the high-pressure hose to the trigger gun and twist the nut as indicated to secure the connection.
6. CONNECT THE HIGH-PRESSURE HOSE TO THE WATER OUTLET
   Connect the other end of the high-pressure hose to the water outlet on the washer and twist the black rotatable end-piece as indicated to secure the connection.
7. CONNECT THE GARDEN HOSE TO THE WATER INLET
   Connect the garden hose adaptor(female coupler) to the water inlet of the pressure washer, then thread your garden hose(male end) into the garden hose adaptor.

Start Up

Pressure Wash

Impurities in the water can damage the high-pressure pump and the accessories. Water supply from mains. Drawing in water from the open reservoir. This high-pressure cleaner is suited to work with the YILI suction hose with h backflow valve to draw in surface water, e.g., from water butts or ponds. Fill the suction hose with water. Screw the suction hose into the water connection of the appliance and insert it into the water source (e.g., rainwater drum).

Bleed the device as follows before the operation.

• Turn on the appliance power switch.
• Unlock the lever of the trigger gun.
• Push the lever of the trigger gun, and the device will switch on.
• Let the device run (max. 2 minutes) until the water exits the trigger gun without bubbles.
• Release the lever of the trigger gun.
• Lock the lever of the trigger gun.

Operation

Dry running of more than 2 minutes leads to damage to the high-pressure pump. If the appliance does not build up pressure within 2 minutes, switch the appliance off and proceed in accordance with the instructions in Chapter “Troubleshooting”.

Washer

Connect the product to the power and water supply as described.

• Open the water supply
• Hold the spray gun with both hands.
• Direct the nozzle of the chosen accessory away from you towards the surface to be cleaned.
• Unlock the trigger and press it until a constant amount of water flows through the nozzle, to allow air trapped in the hose to escape.
• Release the trigger.
• Turn on the switch
• Hold the spray gun with both hands.
• Direct the water jet to the object to be cleaned and press the trigger.

Release the lever of the trigger gun; the device will switch off again and stop the water jet. High pressure remains in the system. WARNING! Beware of kickback when pressing the trigger!

Detergent

Detergent can only be added when the device is operated in low-pressure mode. When using detergents, the material data safety sheet issued by the detergent manufacturer must be adhered to, especially the instructions regarding personal protective equipment.

Remove the cap of the clean detergent bottle. Gently pull the onboard detergent tank out of its storage position. Fill the tank with detergent designed specifically for use with pressure washers. Push the detergent bottle with the opening pointing downwards into the connection for the hose clean detergent.

Cleaning Method

• Spray the detergent sparingly on the dry surface and allow it to react, but not to dry.
• Spray off loosened dirt with the high-pressure Met.
• Remove the hose, clean the detergent bottle from the intake, and close it with the lid.
• For storage, put the detergent bottle into the retainer with the cap pointing up.
• Make sure the on/off switch is set to “OFF” and insert the plug into a properly installed socket.
• Adjust the air flow. Open the air flow block, and suck power will come down. If you close the block, suck power will max. Power.

Interrupting Operation

• Release the lever of the trigger gun.
• Lock the lever of the trigger gun.
• Put the trigger gun with the spray lance into the parking position.
• During longer breaks (more than 5 minutes), also turn the appliance off using the power switch.

Finish Operation

• Release the lever of the trigger gun.
• Turn off the appliance switch pre.
• Disconnect the mains plug from the socket. Only separate the high-pressure hose from the trigger gun or the device when there is no pressure in the system.

Turn Off

• The lever of the trigger gun releases any remaining pressure in the system.
• Release the lever of the trigger gun.
• Lock the lever of the trigger gun.
• Risk of personal injury or damage! Mind the weight of the appliance during transport.

Transportaion

• Switch the product off and disconnect it from the water and power supply.
• Pull out the transport handle until it audibly snaps into place. Attach transportation guards, if applicable.
• Pull the appliance by its transport handle.
• Before horizontal transport, close the cap of the clean detergent bottle.
• Tilt the product towards you until it balances on the wheels. Then move it by its transportation handle.
• Protect the product from any heavy impact or strong vibrations that may occur during transportation in vehicles.
• Secure the appliance against shifting and tipping over.

Storage

Risk of personal injury or damage! Consider the weight of the appliance when storing it

• Park the machine on an even surface.
• Detach the spray lance from the trigger gun.
• Push the disconnect button on the trigger gun and pull the high-pressure hose out of the trigger gun.
• Place the trigger gun into the storage for the trigger gun.
• Put both spray lances into the storage for the spray lances.
• Dirt grinder spray lance: Nozzle towards the bottom.
• Coil the high-pressure hose and hang it over the hose storage.
• Store the mains connection in the accessory compartment.
• Always store the pressure cleaner, parts, and accessories in a place that is inaccessible to children.
• The ideal storage temperature is between 10 °C and 30 °C. Store the power washer indoors to prevent the water in the unit from expanding under freezing conditions.
• We recommend using the original package for storage or covering the product with a suitable cloth or enclosure to protect it against dust.

Frost Protection

• Detach the appliance from the water supply.
• Detach the spray lance from the trigger gun.
• Turn on the appliance power switch.
• Push the lever of the trigger gun until no more water is escaping
• Release the lever of the trigger gun.
• Lock the lever of the trigger gun.
• Turn off the appliance power switch.
• Store the appliance and all accessories in a frost-free room.

Care & Maintainance

Risk of electric shock. Before all work on the appliance, switch off the appliance and pull the power plug.

The high-pressure hose is specially constructed with reinforced walls. It can be easily damaged and should be stored carefully.

• Do not kink.
• Do not drive vehicles over the hose.
• Do not expose the hose to sharp edges or corners. Misuse will lead to ballooning or premature failure and will invalidate the warranty.

Cleaning

Clean the sieve in the water connection regularly. Remove coupling from the water connection, and rinse with warm water to prevent any foreign matter from clogging the pump. Clean the nozzle with the needle clean-out tool provided. Remove the spray wand from the gun. Remove any dirt from the nozzle hole and rinse.

• The sieve must not be damaged.
• Pull the sieve out using flat pliers.
• Clean the sieve under running water.
• Reinsert the sieve into the water connection.

Press the locking block, then push the front to open the dust compartment. Take up the dust compartment. Press the automatic release button to empty the dust into the dust container.

Troubleshooting

Environmental Instructions

• Dispose of cardboard packaging and polyethylene (PE) bags in the appropriate containers for separate collection of municipal waste according to their description.
• If there are batteries in the device, remove them and separately return them to the collection and storage facility. Return the used device to a suitable collection and storage facility, as the hazardous substances in it may pose a threat to health and the environment.
• Waste electrical equipment is waste that contains substances harmful to humans, animals, and the environment.
• These substances can lead to contamination of the soil, water, or air, and through this they can get into the human body and lead to numerous health ailments, such a vision, hearing, and speech disorders; they can also lead to kidney, liver, and heart damage, and cause skin diseases.
• Harmful substances can also have adverse effects on the respiratory and reproductive systems and lead to cancerous changes. Consumption of plants growing on the contaminated soils, and products made from them, may risk the above-mentioned health effects.
• Do not dispose of the device in the municipal waste container!!! Service: If you wish to purchase spare parts or report any complaints, please contact directly with the seller who issued the receipt directly.

Customer Support

• Address: Lyoner Str. 36 60528 Frankfurt am Main
• Tel:+49 69 310 900 66
• Website: www.ronixtools.com

FAQs

What is the power and pressure rating of the RP-4100?

With its strong electric motor and high cleaning pressure (check your model label for the precise PSI/bar rating), the RP-4100 effectively removes dust, muck, and oil.

Can I use the RP-4100 with hot water?

No, only cold or slightly warm water (up to 40°C/104°F) is suitable for the RP-4100. Using hot water can harm the pump system and internal seals.

How do I assemble the accessories?

Connect the preferred spray gun or nozzle to the hose outlet until it clicks firmly. If you intend to use cleaning solutions, connect the foam lance or detergent bottle.

What type of detergent should I use?

Only use the water-based, non-corrosive cleaning solutions that are suggested for pressure washers. Steer clear of flammable substances, solvents, and bleach since they can harm internal parts and seals.

How do I use the detergent function?

Pour an appropriate cleaning solution into the foam bottle or detergent tank. Connect it to the spray gun or specified intake, then turn on the detergent flow by choosing the low-pressure setting on the nozzle.

How long can I run the RP-4100 continuously?

It is advised to run the machine constantly for no more than 20 minutes to avoid overheating. To prolong motor life, give it a 5- to 10-minute break in between sessions.

Is the RP-4100 waterproof?

Although it is approved for outdoor use, the RP-4100 is not completely waterproof. Avoid submerging the device or leaving it outside in persistent rain.

Can I use an extension cord with the RP-4100?

Yes, but be sure the extension cord is rated for the machine’s power needs, heavy-duty, and correctly grounded. Using a cord that is too small might lead to overheating and decreased efficiency.