Makita DCB18WA Basic Battery Charger
Introduction
The Makita DCB18WA Basic Battery Charger is designed for safe and efficient charging of Makita 18V Li-Ion batteries. The charger is compatible with various Makita 18V Li-Ion tools, including drills, drivers, and routers. For detailed instructions on using the Makita RP0900 8mm 900W Plunge Router, see the Makita RP0900 Plunge Router Instruction Manual. Before use, familiarise yourself with the symbols and safety instructions.
Safety Instructions
- This manual contains important safety and operating instructions for the battery charger.
- Non-rechargeable batteries cannot be charged with this battery charger.
- Use a power source with the voltage specified on the nameplate of the charger.
- Do not charge the battery cartridge in the presence of flammable liquids or gases.
- Do not expose the charger to rain, snow, or wet conditions.
- Never carry a charger by the cord or yank it to disconnect from the receptacle.
- Remove the battery from the charger when carrying the charger.
- Before attempting any maintenance or cleaning, unplug the charger from the power source.
- Pull by plug rather than cord whenever disconnecting the charger.
- Do not operate the charger with a damaged cord or plug.
- Incorrect use or reassembly may result in a risk of electric shock or fire.
- Do not attempt to use a step-up transformer, an engine generator, or a DC power receptacle.
- Do not allow anything to cover or clog the charger vents.
- Do not plug or unplug the cord and insert or remove the battery with wet hands.
Charging
To start charging, insert the battery into the Makita DCB18WA Basic Battery Charger. The charging light will illuminate, indicating that the device is functioning properly.
-
- Plug the battery charger into the proper AC voltage source.
- Insert the battery cartridge into the charger until it stops adjusting to the guide of the charger.
- The charging light will keep lighting up steadily during charging.
- After charging, remove the battery cartridge from the charger.
| Voltage | Number of cells | Li-ion battery cartridge | Capacity (Ah) | Charging time (Minutes) |
| 18 V | 5 | BLB182 | 2.0 | 90 |
Wall mounting
The Makita DCB18WA Basic Battery Charger can be mounted on a wall using the provided screws for a secure setup.
- Make sure to use two screws for hanging the charger on the wall, and anchor the charger on the wall with another screw. Otherwise, the charger may fall and cause serious injury.
- Always be sure that the charger is unplugged and the battery is removed from the charger before performing wall mounting work.
- Follow the steps instructed in this manual, and complete the whole procedure at once.
- The charger may fall and cause injury or damage if you stop the work in the halfway.
- Check the tightness of the screws regularly. Otherwise, the charger may fall because of a lloosescrew.
- Clean the terminal parts of the charger on a regular basis with an air duster, etc.
You can mount the charger on the wall. Make a clearance around the charger as shown in the figure.
- Fix two screws for hanging on the wall.
- Hang the charger on the wall using the hook on the back.
- Fix the charger by tightening an anchor screw at the top of the charger.
Customer Service
- Website:Â https://www.makitauk.com/
- Ph:Â 1-800-462-5482
FAQs
Q: What is the Makita DCB18WA used for?
Makita 18V Lithium-Ion batteries can be safely charged with the Makita DCB18WA, a small, simple battery charger. It’s perfect for people who require simple, dependable charging for regular usage of power tools.
Q: Which batteries are compatible with the DCB18WA charger?
It works with Makita 18V Li-Ion slide-type batteries (usually 1.3Ah to 3.0Ah) from the LXT line. Ni-MH, Ni-Cd, and CXT 12V batteries are incompatible with it. Prior to connection, always read the battery label.
Q: Can it charge high-capacity batteries (like 4.0Ah or 5.0Ah)?
The DCB18WA is mainly intended for batteries with a normal capacity (up to 3.0Ah). Depending on the firmware and model variation, charging larger-capacity batteries may take longer or not be supported.
Q: Can I leave the battery in the charger after it’s fully charged?
Yes, for brief intervals. When the battery is full, the charger automatically enters maintenance mode. But to prolong its life, take the battery out for long-term storage.
Q: Does the charger have overcharge protection?
Indeed. Overcharge, overcurrent, and overheat protection are all integrated into the DCB18WA, guaranteeing safe charging without causing battery damage.
Q: Can I use it with any power source?
Use only 230V AC outlets. Unless they are rated for delicate electrical equipment, avoid connecting to generators or inverters that generate erratic voltage.
Q: Can I use it outdoors?
The charger should only be used indoors. Steer clear of wetness, precipitation, and extremely high or low temperatures.
Q: What happens if the charger gets too hot?
To safeguard internal components, the charger automatically lowers the current or stops charging. Before using it again, let it cool naturally.