ADLER AD 7065 Cyclone Vacuum Cleaner Instructions Guide

ADLER AD 7065 Cyclone Vacuum Cleaner

Safety Instructions

1. Before using the device, read the instruction manual and follow the instructions contained therein.
2. The device is for domestic use only. Do not use it for other purposes incompatible with its intended use.
3. The device should be connected only to a 220-240V ~50-60 Hz grounded outlet.
4. Take special care when using the device when children are around. D
5. o not allow children to play with the appliance.
6. Do not allow children or persons\ unfamiliar with the appliance to use it.
7. Always after use, remove the plug from the power outlet by holding the outlet with your hand.
8. DO NOT pull on the power cord.
9. Do not immerse the cable, plug, or the entire device in water or other liquid.
10. Do not repair the device yourself, as there is a risk of electric shock.
11. Take the damaged device to a competent service center for inspection or repair.
12. All repairs may be carried out only by authorized service centers.
13. Improper repair may cause danger to the user.
14. Do not use the device near flammable materials.
15. The power cord must not touch hot surfaces.
16. Do not leave the device or the power supply to the outlet unattended.
17. Do not let the motor part of the device get wet.
18. Do not use the device outside the home; use it only indoors.
19. Do not use the vacuum cleaner to collect flammable substances (such as fuel, solvents).
20. Do not vacuum sharp-edged objects (such as glass shards).
21. Do not point the suction tube of the vacuum cleaner towards other people or animals.
22. Vacuum only dry surfaces.
23. Use only accessories designed for this device.
24. Take special care when vacuuming stairs, and take care of your safety.
25. Do not block any ventilation holes..

Description

1. floor/carpet brush
2. floor/carpet switch
3. telescopic tube button
4. Telescopic extension tube
5. flexible hose holder
6. manual adjustment of suction power
7. flexible hose
8. flexible hose end
9. hose end locks
10. air inlet
11. Complete dust container.
12. carrying handle
13. dust container lock button
14. power cord retraction button
15. parking position hanger
16. power button
17. suction power knob
18. outlet filter cover
19. HEPA 13 filter
20. Lower the dust container cover
21. Locking device of the lower dust container cover
22. Dust container housing
23. Dust container upper cover
24. Cyclone filter
25. inlet filter
26. Sponge filter
27. Accessory holder
28. Crevice tool
29. Upholstery brush 2-in-1
30. Mini-turbo brush
31. parquet brush

Before First Use

After transporting or storing the device in sub-zero temperatures, unpack it and wait at least 3 hours before using it.

Use of Accessories

• Floor/carpet brush (1): When using the brush (1), set the switch (2) to the desired “FLOOR/carpet” position.
• Crevice nozzle (28): Use the crevice nozzle (28) to clean radiators, crevices, spaces between couch cushions, and the like.
• Upholstery brush (29): It is designed to clean fabric surfaces of upholstered furniture and to collect dust from the surface of furniture, while the presence of fibers on the brush (29) prevents damage to the polished surface of furniture. When working, put the brush on the cap (29).
• Mini-turbo brush (30): It is designed for cleaning fabric surfaces in hard-to-reach corners, such as the interior of a car.
• Parquet brush (31): It is designed for cleaning wooden surfaces.

Assembly

Inserting and removing the flexible hose (7).

Insert the end of the flexible hose (7) (8) into the air inlet (10) until the latches (9) snap into place. To remove the flexible hose (7), push in the latches (9) and disconnect the end (8) from the air inlet (10).

Attaching the telescopic tube (4) and accessories

Attach the telescopic extension tube (4) to the flexible hose holder (5). Extend the lower part of the tube (4) to the required length after pressing the button (3). Select the necessary accessories:

•  floor/carpet brush (1),
•  crevice nozzle (28)
•  2-in-1 upholstery brush (29)
•  mini-turbo brush (30)
•  parquet brush (31) and then attach it to the telescoping extension tube (4).

The crevice nozzle (28) and the 2-in-1 upholstery brush (29) can be attached to the flexible hose holder (5).

Using the Device

1. The dust container (11) is equipped with a cyclone filter (24), which centrifuges debris and dust from the sucked air, while the inlet filter (25) and sponge filter (26) trap the finest dust particles.
2. Before turning on and using the vacuum cleaner, make sure that the cyclone filter (24), filters (25, 26), dust container (11), and HEPA exhaust filter (19) are properly installed.
3. Remove the power plug and unroll the power cord to the required length, and plug the power plug into the power outlet.
4. The yellow marking on the power cord indicates the maximum length of the cord. Do not extend the power cord further than the red mark.
5. Press the power button (16) to turn on the vacuum cleaner.
6. While cleaning, you can adjust the suction power with the manual suction power regulator (6) on the flexible hose handle (5) or by turning the suction power adjustment knob (17).
7. When you have finished cleaning, turn off the vacuum cleaner by pressing the power button (16) and unplugging it.
8. To retract the power cord, press the button (14); hold the cord with your hand while retracting it.
9. If you need to take a break during cleaning, turn off the vacuum cleaner by pressing the power button (16) and attach the brush (1) to the parking position hanger (15).

Cleaning & Maintainance

• It is recommended to remove debris and dust from the dust container (11) after each cleaning of the room.
• Turn off the vacuum cleaner by pressing the power button (16) again and unplugging it.
• Hold the dust container handle, press the lock (13), and remove the entire dust container (11) (Fig. II.1).
• Place the entire dust container (11) over the dust garbage can.
• Press the clamp (21), and then the lower cover (20) will drop down, releasing dust and fine debris (Fig. II.2).
• Remove accumulated dust and debris from the dust garbage can (11), if it still does not fall into the dust garbage can.
• Close the lower cover (20).
• Install the entire dust bin (11) back in place and make sure the dust bin (11) is properly fastened.

Cleaning the filters (24), (25), (26).

The cyclone filter (24) and filters (25, 26) are installed in the dust bin (11). Preliminarily remove dust and debris from the dust container (11) as described above.

1. Turn the cover (23) counterclockwise and remove it.
2. Remove the sponge filter (26), take out the inlet filter (25), and the cyclone filter (24).
3. Clean the cyclone filter (24) of dust and debris.
4. Wash the cyclone filter (24) under a stream of warm water and dry completely.
5. Wash the inlet filter (25) and sponge filter (26) under a stream of warm water and dry.
6. Dry the filter (25, 26) completely.
7. Do not dry any filter with a hair dryer or similar device. Do not wash parts in a dishwasher.
8. Wash the dust container housing (22), wipe it, and dry it.
9. Insert the cyclone filter (24) into the dust container housing (22).
10. Insert the inlet filter (25) and sponge filter (26) into the cyclone filter (24).
11. Replace the cover (23) and turn it clockwise as far as it will go.
12. Install the completely assembled dust container (11) back into place, making sure that the entire dust container (11) is properly attached.

Cleaning the HEPA 13 exhaust filter (19).

Turn off the vacuum cleaner and remove the power cord plug from the power outlet.

• Remove the outlet filter cover (18) by turning it clockwise, and remove the HEPA outlet filter (19) (Fig. II.3).
• Wash the HEPA 13 outlet filter (19) and cover (18) under a stream of lukewarm water. Do not wash the HEPA outlet filter 13 (19) and cover (18) in the dishwasher.
• Dry HEPA outlet filter 13 (19) and cover (18). Do not dry HEPA filter 13 (19) with a hair dryer or similar device.
• Install the HEPA outlet filter 13 (19) back into place.
• Put the cover (18) back in place, turn the cover (18) counterclockwise until it stops.

Vacuum cleaner housing

1. Clean the vacuum cleaner housing with a soft, slightly dampened cloth, then wipe dry. Be careful that no liquid gets into the vacuum cleaner body.
2. Do not use solvents or abrasives to clean the vacuum cleaner body and accessories.
3. Do not immerse the vacuum cleaner body, power cord, or plug in water or other liquids.

Protection Against Overheating

1. If the electric motor ADLER AD 7065 Cyclone Vacuum Cleaner overheats during operation, the overheat protection system will be activated, and the device will shut down automatically.
2. In this case, press the power button (16) and unplug the device.
3. Wait 30-40 minutes for the vacuum cleaner to cool down and turn it on again. The cooling time may differ from the specified value depending on the temperature in the room.
4. If the vacuum cleaner does not turn on, it may be due to another malfunction. In this case, contact the dealer’s service center indicated on the purchase receipt.

Storage

1. Before putting the vacuum cleaner away for a long period of time, clean the vacuum cleaner body, dust container outside and inside, cyclone filter (24), filters (25, 26), and HEPA exhaust filter (19).
2. To make it easier to store the vacuum cleaner, use the parking position hanger (16) to attach the tube(4) and hose (7).
3.  Attach the accessory holder (27) to mount the crevice nozzle (28) and 2-in-1 upholstery brush (29).Store
4. The vacuum cleaner in a dry and cool place, out of the reach of children and people with disabilities.

The complete set consists of

1.  Vacuum cleaner with an installed dust container and filters
2. flexible hose
3.  Telescopic extension tube
4. floor/carpet brush
5. crevice tool
6. Upholstery brush 2-in-1
7. Mini-TURBO brush
8. Parquet brush
9. crevice nozzle
10. instruction manual
11. Hanger for accessories

Technical Specifications

• Power supply: 220-240V~ 50-60Hz
• Rated power: 700W
• Suction power: 170W
• Dust container capacity: 1.6 liters

Environmental Instructions

• Dispose of cardboard packaging and polyethylene (PE) bags in the appropriate containers for separate collection of municipal waste according to their description.
• If there are batteries in the device, remove them and separately return them to the collection and storage facility. Return the used device to a suitable collection and storage facility, as the hazardous substances in it may pose a threat to health and the environment.
• Waste electrical equipment is waste that contains substances harmful to humans, animals, and the environment.
• These substances can lead to contamination of the soil, water, or air, and through this they can get into the human body and lead to numerous health ailments, such a vision, hearing, and speech disorders; they can also lead to kidney, liver, and heart damage, and cause skin diseases.
• Harmful substances can also have adverse effects on the respiratory and reproductive systems and lead to cancerous changes. Consumption of plants growing on the contaminated soils, and products made from them, may risk the above-mentioned health effects.
• Do not dispose of the device in the municipal waste container!!! Service: If you wish to purchase spare parts or report any complaints, please contact directly with the seller who issued the receipt directly.

Customer Service

• Website:  service@adlerglobal.com. 
• Ph: 0800 9753 003
• Timings:  Mo – Fr, 8:30 am – 5:00 pm