ADLER AD 1304 Ceramic Electric Kettle
Safety Instructions
- Before using the device, read the instruction manual and follow the instructions contained therein.
- The device is for domestic use only. Do not use for other purposes; incompatible with its purpose.
- Connect the device only to a grounded outlet 220-240V ~50/60Hz.
- Take special care when using the device when children are around.
- Do not allow children to play with the device.
- Do not allow children or anyone unfamiliar with the device to use it.
- Do not use the device if its housing is cracked.
- Do not open the lid if the water is boiling.
- Do not leave the appliance plugged into an outlet unattended.
- Keep the device out of the reach of children.
- Always remove the plug from the power outlet after use by holding the outlet with your hand.
- DO NOT pull on the power cord.
- Do not move the unit while it is in use.
- Do not immerse the cord, plug, or entire unit in water or other liquid.
- Do not use the device near flammable materials.
- The power cord must not hang over the edge of the table or touch hot surfaces.
Description
- Lid
- handle for opening the lid
- casing
- handle
- base
- filter
- control panel
- brewing basket
- indicator light
Before First Use
Fill the kettle with water three times to the maximum level, boil, and pour out. To remove any factory odor. Touch the buttons on the touch panel (8) only with your fingers;s, touching with your fingernails may damage the panel.
Basic Operation
- Set the base (5) on a stable, flat, and heat-resistant surface.
- Fill the kettle with water so that the water level is between the maximum and minimum levels on the water level indicator in the center of the kettle.
- Remember to close the kettle’s lid (1) after filling, otherwise the kettle will not turn off automatically when the water boils.
- Plug the power cord plug into a 220-240V ~50/60Hz grounded power outlet. Place the kettle on the base (5). You will hear a “di” sound, the touch panel (8) will light up, and the LCD (2) will indicate the current water temperature.
- Press the (A) “On/Off” button, the (H) temperature hold indicator, and the “+”(F), “-” (G) indicator will light up, and the heater will start heating water. The LCD (2) will start to indicate the current water temperature. The water temperature will increase until boiling, that is, up to 100°C.
- After the water boils, the kettle will automatically turn off, and you will hear a “di-di” sound twice. The LCD (2) will indicate 100°C, then after 25 seconds it will turn off, and the icon (A) On/off will
flash. - Want to turn off the kettle before the water is finished boiling, lift it from the base (5) or press the On/Off button (A).
- You can start turning the kettle on again about 2 minutes after the last u. For this purpose, press the (A) “On/Off” button.
Warm Function
Place the kettle on the base (5), you will hear a “di” sound. Press one of the temperature selector buttons on the panel (8), then press the temperature hold Adler AD 1299 Stylish Glass Electric Kettle button (H). The indicator (H) will start flashiflashinch means that the temperature hold function is on.
After reaching the set temperature, the kettle will enter the temperature hold mode and will cycle the water when the water temperature drops by 5℃ from the selected temperature level.
If the water temperature in the kettle is higher than the desired temperature (more than 5℃), the temperature hold function indicator will flash until the water cools down to the pre-set temperature, being in temperature hold mode all the time.
To interrupt the temperature hold function, remove the kettle from the base (5) or press the button (A).
Cleaning & Maintainance
This activity is not subject to warranty service. Failure to decalcify regularly will lead to damage to the kettle and void the warranty. To decalcify, use specially designed preparations for this purpose in accordance with the instructions for use of the decalcifying agent. After decalcification, rinse the kettle very thoroughly three times.
Specifications
- Capacity max: 1.7L min: 0.5L
- Voltage: 220-240V ~50/60Hz
- Power: 1850-2200W
Customer Service
- Website: service@adlerglobal.com.
- Ph: 0800 9753 003
- Timings: Mo – Fr, 8:30 am – 5:00 pm
FAQs
Q: What is the power rating of the ADLER AD 1304 kettle?
Depending on your location, the kettle runs at 1500–1800W, which guarantees rapid and effective boiling.
Q: What is the maximum water capacity?
With its 1.7-liter capacity, the kettle is perfect for making several cups of tea, coffee, or other hot liquids.
Q: Is the kettle made of metal or plastic?
The ceramic body of the AD 1304 gives a sophisticated, heat-resistant finish while also assisting in regulating the water’s temperature.
Q: Does the kettle have an automatic shut-off?
Indeed, it has an automatic shut-off feature that prevents dry boiling and improves safety when the water exceeds the boiling point.
Q: Is there a boil-dry protection feature?
Yes, the kettle will immediately shut off to prevent harm if it is turned on without water or if the water level is too low.
Q: Is the kettle suitable for hard water areas?
Yes, but in order to avoid mineral accumulation on the heating element, periodic descaling is advised.
Q: Can I leave water in the kettle overnight?
Standing water can alter flavour and encourage the growth of bacteria; thus, it is not advised. After use, empty.
Q: Is the kettle safe for children?
Yes, under supervision. Though care should be taken when near boiling water, the ceramic exterior is still cooler than metal.