ADLER AD 1305 White Electric Kettle Instructions Guide

ADLER AD 1305 White Electric Kettle

Safety Instructions

1. Before using the device, read the instruction manual and follow the instructions contained therein.
2. The device is for domestic use only. Do not use for other purposes; incompatible with its purpose.
3. Connect the device only to a grounded outlet 220-240V ~ 50/60Hz.
4. Take special care when using the device when children are around.
5. Do not immerse the cord, plug, or entire unit in water or other liquid.
6. Periodically check the condition of the power cord.
7. If the power cord is damaged, it should be replaced by a specialized repair facility to avoid danger.
8. Do not repair the device yourself, as there is a risk of electrocution.
9. Return a damaged device to a competent service center for inspection or repair.
10. All repairs may be made only by authorized service centers. Improper repair may cause danger.
11. Do not use the device near flammable materials.
12. The power cord must not hang over the edge of the table or touch hot surfaces.
13. If the kettle is overfilled, boiling water may gush out of it.
14. Carry the kettle only by holding the handle.
15. Do not turn on the kettle without water, as this may cause damage to the kettle.
16. Do not use the kettle without a filter or with the lid open, as the circuit breaker will not work then.
17. Periodically, the kettle should be decalcified using means designed for this purpose.
18. Using a kettle with a calcified heater will damage it and void the warranty.
19. The device is not designed to operate with external timers or a separate remote control system.
20. Do not wash the base of the kettle directly in water; only wipe with a dry cloth.

Description

1. Lid
2. LCD
3. Case
4. Holder
5. Base
6. Button to open the lid
7. MIN/MAX water level indicator
8. Touch panel

   • 

     On/Off button – temperature setting 100℃

   • Temperature setting button 40℃
   • Temperature setting button 70℃
   • Temperature setting button 80℃
   • Temperature setting button 90℃
   • Temperature setting button + 5℃
   • Temperature setting button – 5℃
   • Temperature hold button

Before First Use

Fill the kettle with water three times to the maximum level, boil, and pour out. To remove any factory odor. Touch the buttons on the touch panel (8) only with your fingertips; touching with your fingernails may damage the panel.

Basic Operation

1. Set the base (5) on a stable, flat, and heat-resistant surface.
2. Fill the kettle with water so that the water level is between the maximum and minimum levels on the
   water level indicator in the center of the kettle.
3. Remember to close the kettle’s lid (1) after filling, otherwise the kettle will not turn off automatically when the water boils.
4. Plug the power cord plug into a 220-240V ~50/60Hz grounded power outlet. Place the kettle on the base (5). You will hear a “di” sound, the touch panel (8) will light up, and the LCD (2) will indicate the current water temperature.
5. Press the (A) “On/Off” button, the (H) temperature hold indicator, and the “+”(F), “-” (G) indicator will light up, and the heater will start heating water.
6. The LCD (2) will start to indicate the current water temperature. The water temperature will increase until boiling, that is, up to 100°C.
7. After the water boils, the kettle will automatically turn off, and you will hear a “di-di” sound twice.
   The LCD (2) will indicate 100°C, then after 25 seconds it will turn off, and the icon (A) On/off will flash.
8. You can start turning the kettle on again about 2 minutes after the last use; for this purpose, press the (A) “On/Off” button.
9. The kettle also has a function to set the ADLER AD 1305 White Electric Kettle temperature from 40℃ to 100℃ in 5℃ increments.
10. To do this, use the F(+) and G (-) buttons to increase the F (+) temperature or decrease the G (-) temperature.

Advanced Operation

Place the kettle on the base (5), you will hear a “di” sound. Press the temperature selection button 40℃  (B),70℃ (C), 80℃ (D), or 90℃ (E), the LCD (2) will show your selected temperature of 40℃, 70℃, 80℃
or 90℃, then the LCD (2) will show the current water temperature inside the kettle. The temperature hold indicator (H) and on/off indicator (A) will light up, and the heater will start heating the water.

The kettle will stop boiling water when the selected temperature level reaches 40℃, 70℃, 80℃, or 90℃.
Will hear a “dii-di” sound twice. The LCD (2) will indicate the temperature reached, then after 25 seconds it will turn off, and the indicator (A) On/Off will flash.

If you want to turn off the kettle before the water has finished boiling, lift it from the base (5) or press the
On/Off button (A). You can start turning the kettle on again about 2 minutes after the last use; for this purpose, press the (A) “On/Off” button.

Warm Function

Place the kettle on the base (5), you ADLER AD 1305 White Electric Kettle will hear a “di” sound. Press one of the temperature selector buttons on the panel (8), then press the temperature hold button (H).

The indicator (H) will start flashing, which means that the temperature hold function is on. After reaching the set temperature, the kettle will enter the temperature hold mode and will cycle the water when the water temperature drops by 5℃ from the selected temperature level.

If the water temperature in the kettle is higher than the desired temperature (more than 5℃), the temperature hold function indicator (G)  will flash until the water cools down to the pre-set temperature, being in temperature hold mode all the time. To interrupt the temperature hold function, remove the kettle from the base (5) or press the button (A). The temperature hold function is maintained for 2 hours after the last boil.

Features

The appliance is equipped with an automatic overheat fuse; the fuse will activate when it has been used with insufficient water. Always make sure that the amount of water in the appliance is above the minimum level. If the fuse engages, turn off the kettle by pressing button (A), then remove the plug from the power socket and let the kettle cool down for 5-10 minutes. Then fill the kettle with water and turn on the
appliance, which will operate normally.

Turning on an empty kettle or one insufficiently filled with water will automatically turn off the device. In this case, wait several minutes. Pour the appropriate amount of water and turn the kettle on again. Do not leave the switched-on kettle unattended. The kettle is an electrical appliance not designed to hold water or any other liquids. After boiling the water, pour it immediately into another vessel. Water after boiling in the kettle must not remain in it for more than 10 minutes. Before each use, fill the kettle with fresh water above the minimum level and below the maximum level.

Cleaning & Maintainance

Limescale deposited inside the kettle, ADLER AD 1305 White Electric Kettle, should be removed regularly. This activity is not subject to warranty service. Failure to decalcify regularly will lead to damage to the kettle and void the warranty. To decalcify,
use specially designed preparations for this purpose according to the instructions for use of the decalcifying agent. After decalcification, rinse the kettle very thoroughly three times.

Specifications

• Capacity max: 1.7L min: 0.5L
• Voltage: 220-240V ~50/60Hz Power: 1850-2200W

The temperature of the accessible surfaces of the running appliance may be high. Do not
touch the hot surfaces of the unit

Environmental Instructions

• Dispose of cardboard packaging and polyethylene (PE) bags in the appropriate containers for separate collection of municipal waste according to their description.
• If there are batteries in the device, remove them and separately return them to the collection and storage facility. Return the used device to a suitable collection and storage facility, as the hazardous substances in it may pose a threat to health and the environment.
• Waste electrical equipment is waste that contains substances harmful to humans, animals, and the environment.
• These substances can lead to contamination of the soil, water, or air, and through this, they can get into the human body and lead to numerous health ailments, such as vision, hearing, and speech disorders; they can also lead to kidney, liver, and heart damage, and cause skin diseases.
• Harmful substances can also have adverse effects on the respiratory and reproductive systems and lead to cancerous changes. Consumption of plants growing on the contaminated soils, and products made from them, may risk the above-mentioned health effects.
• Do not dispose of the device in the municipal waste container. Service: If you wish to purchase spare parts or report any complaints, please contact the seller who issued the receipt directly.

Customer Service

• Website:  service@adlerglobal.com
• Ph: 0800 9753 003
• Timings:  Mo – Fr, 8:30 am – 5:00 pm