NEBULA Capsule Air Smallest Google TV Projector User Guide

NEBULA Capsule Air Smallest Google TV Projector

Front View

Rear View

Speaker

Infrared Receiver Power Button

• Press and hold for 1.5 seconds to power on / off.
• Press to wake up the projector / enter standby mode in projector mode. USB-C Port
• Connect to a USB drive.
• Connect to a power source via a charging cable. HDMI Port
• Connect to a playback device via HDMI output

Top View

Volume Up / Down Buttons Confirmation Button Return Button Navigation Buttons

LED Light Guide

Bottom View

1/4″ Tripod Socket

1. Slide to open the battery compartment.
2. Insert new batteries matching the polarity (+/-) and close the battery compartmen
3. For first-time use, follow the on-screen instructions to pair the remote with your projector.

Place the projector on a stable, flat surface in front of the projection surface. For the best results, the projection surface should be white and flat.

• It is unnecessary to tilt the projector towards the projection surface. You can correct the projection image with the built-in autofocus and auto-keystone correction.
• You may also install the projector onto a tripod (sold separately).
• The distance between the projector and the projection surface determines the projection image size. For the best result, position the projector 0.5 – 2.7 m / 1.64 – 8.86 ft away from the projection surface to get a screen size of 40~120 inches.

For first-time use, fully charge your projector using the provided adapter and charging cable.

Press and hold the projector power button for 1.5 seconds to power on / off.

• When the projector is connected to an adapter, you can use the remote control to power it on.
• In HDMI Source Mode, the projector will switch to standby mode after 10 minutes of button inactivity or when no signal is detected.
• When standby mode lasts for 30 minutes, the projector will automatically power off.

How to trigger auto focus

• a. Press the [Auto image adjustment] button on the remote control.
• b. Auto-trigger upon powering on.
• c. Auto-trigger after moving the projector. How to perform manual focus: Go to [Settings] > [Projector] [Focus Settings] > [Manual Focus Correction].

How to trigger Auto Keystone Correction

After enabling Auto Keystone Correction in [Settings] > [Projector] > [Image Correction] > [Auto Keystone Correction Settings], Auto Keystone Correction will be triggered in the following scenarios:

• a. Pressing the [Auto image adjustment] button on the remote control.
• b. Auto-trigger upon powering on.
• c. Auto-trigger after moving the projector.

How to perform manual keystone correction

Go to [Settings] > [Projector] > [Image Correction] > [Perform Manual Keystone Correction].

When using the projector for the first time, follow the on-screen display (OSD) instructions to complete the basic setup.

1. Firmly attach the Nebula Capsule Air to the Snap-on Base by aligning the projector’s bottom with the base’s inner circle and turning it clockwise.
   
2. Now you’re ready to enjoy your favorite content wherever you like.

To Mount the Snap-on Base on the Wall

1. Prepare the template paper, Snap-on Base, two screws, and two plastic anchors
2. Fix the provided template paper on the wall, and drill two holes according to the specified locations.

Please use a 6mm diameter drill bit.

Spec’s

1. Insert the plastic anchors into the drilled holes
2. Secure the Snap-on Base to the wall using the provided screws, and make sure it’s firmly attached.
3. Now you can adjust the projecting angle as you like.
4. When mounted on the wall, the maximum tilt angle is 90°.

To easily control the projector, we recommend you download the Nebula Connect app.

1. Download the Nebula Connect app from the App Store (iOS devices) or Google Play (Android devices).
2. Enable Bluetooth on your smartphone.
3. Open the Nebula Connect app and select [Capsule Air] as the device to be connected.
4. Follow the on-screen instructions to complete the connection setup.

This projector can be connected to the Internet via a wireless (Wi-Fi) connection.

1. On the home page, select > [Network & Internet] and press confirm.
2. Follow the on-screen instructions to complete the network connection.

1. On the home page, select > [Apps] and press confirm.
2. Select an app to check its current version, open or force stop it, review the storage it uses, clear its data or cache, uninstall it, or enable/ disable its notifications and permissions.

On the home page, select 

Once connected to a wireless network, you can access online services, enjoy movies, music,c and pictures, and browse online. You can download more apps from Google Play.

1. Press to access the home page.
2. Select [Apps] > [Search for apps and games].

After pairing your remote control with the projector via Bluetooth, press the Google Assistant button on the remote. You can speak to the Google Assistant and request your commands.

You can wirelessly cast movies, games, music, and the entire screen from your iOS, macOS, Android, or Windows device to Nebula Capsule Air. Make sure Nebula Capsule Air and your device are connected to the same wireless network. The network can be a WiFi network or your phone’s hotspot.

Cast In-App Content

You can cast content from apps that support Chromecast, such as YouTube and Prime Video.

For iOS Devices

1. Ensure both the projector and your iOS device are connected to the same Wi-Fi network.
2. On the projector, install and open the Nebula Cast App from Google Play.
3. Open the Control Center on your iPhone, tap on Screen Mirroring, find “Nebula Capsule Air” in the device list, and tap to connect.

For Android Devices

1. Ensure both the projector and your Android device are connected to the same WiFi network.
2. Install and open the Google Home App on your device.
3. Add a new device, find “Capsule Air” and connect.

Certain content cannot be cast on Nebula Capsule Air due to copyright restrictions. You can stream the content via the same app installed on your projector.

1. Connect the projector to an HDMI playback device with an HDMI cable (not provided).

[Inputs]  [HDMI]

The projector will automatically start HDMI playback once connected to an HDMI playback device for the first time.

To play from a USB drive

Since the projector has only one USB-C port, you will need to use a hub to charge the device and read a USB drive simultaneously.

Instructions

1. Connect the hub to the projector’s USB-C port.
2. Plug the charger into the hub’s charging port.
3. Insert the USB drive into the hub’s USB port.

You can use this projector as a standalone Bluetooth speaker.

1. Go to [Settings] > [Display & Sound] > [Sound] > [Turn on the Bluetooth Speaker Mode] to switch your Nebula projector from Projector Mode to Bluetooth Speaker Mode.
2. Go to Bluetooth settings on your phone to pair with your Nebula projector.

To exit Bluetooth Speaker Mode, press the return button on the remote control.

1. Turn on your Bluetooth speaker and set it to pairing mode (refer to your speaker’s manual for specific instructions,s as the process may vary).
2. Go to [Settings] > [Remotes & Accessories] in the project’s settings. Find your Bluetooth speaker’s name and select it to pair.
3. Once paired successfully, the projector’s audio will be output through
   the external Bluetooth speaker.

To update the system, go to [Settings] > [System] > [About] > [System update].

Specifications

1.  Fails to Power On
   • The projector may be out of power.
2. Cannot Charge
   • Use the included adapter and charging cable to charge the projector.
3. Cannot Connect to a Wi-Fi Network
   • Place your projector within 16 ft / 5 m of the router and reconnect.
   • Set your router to 2.4 GHz or 5 GHz and retry.
   • Restart your projector and router and retry.
   • Try a different Wi-Fi network or your phone’s hotspot.
4. Blurry Image
   • Slightly move the projector or press on the remote to start autofocus.
   • To manually adjust the focus, go to [Settings] > [Projector] > [Focus Settings] > [Manual Focus Correction], and use left and right on the remote.
5. Distorted Image
   • Update the firmware to the latest version via [Settings] > [System] > [About] > [System update].
   • Go to [Settings] > [Projector] > [Image Correction] > [Perform Manual Keystone Correction].
6. No HDMI Signal
   • Use a different HDMI cable.
   • Connect the HDMI playback device to your TV via an HDMI cable to
   • Adjust the HDMI playback device’s output resolution/frequency to be the same as the projector’s.
7. How to Play Videos without Wi-Fi
   • Download videos to a USB drive in FAT32 format.

Bluetooth

The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc., and any use of such marks by Anker Innovations Limited is under license. Other trademarks and trade names are those of their respective owners.

HOMI

HIGH-DEFINITION MULTIMEDIA INTERFACE HDMI, and HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries. • Dolby

AUDIO

Manufactured under license from Dolby Laboratories. Dolby, Dolby Audio, and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation.

Customer Support

• Website: https://www.asknebula.com/