Vevor 8840-D8840-8850E Magnetic Drill – High-Power Drilling
Close Menu
    Vevor

    Vevor 8840-D8840-8850E Magnetic Drill Instructions Guide

    By Updated:No Comments8 Mins Read

    Vevor-logo

    Vevor 8840-D8840-8850E Magnetic Drill

    Vevor-8840-D8840-8850E-Magnetic-Drill-PRODUCT

    Safety Instructions

    1. Keethe p the work area clean and well-lit. Cluttered or dark areas invite accidents.
    2. Keep children and bystanders away while operating a power tool.
    3. Distraction can cause you to lose control.
    4. When the construction is completed, the switch must be turned off before leaving.
    5. Power tool plugs must match the outlet. Never modify the plugin anyway.
    6. Do not use any adapter plugs with earthed (grounded) power tools.
    7. Unmodified plugs and matching outlets will reduce the risk of electric shock.
    8. Do not expose power tools to rain or wet conditions.
    9. Water entering a power tool will increase the risk of an electric shock.
    10. Do not abuse the cord. Never use the cord for carrying, pulling unplugging the power tool.
    11. Keep cord away from heat, oil, sharp edges,, moving parts.
    12. Damaged or entangled cords increase the risk of electric shock.
    13. When operating a power tool outdoors, use an extension cord suitable for outdoor use.
    14. Use of a cord suitable for outdoor use reduces the risk of electric shock.
    15. Stay alert, watch what you are doing, and use common sense when operating a power tool.
    16. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication.
    17. A moment of inattention while operating power tools may result in serious personal injury.
    18. Use personal protective equipment. Always wear eye protection.

    Model & Parameters

    Model 8840 D8840 8850E D8860
    Hole diameter (hollow drill)(mm) Φ40mm Φ40mm Φ50mm Φ50mm
    Fried dough twist drill diameter(mm) Φ3-Φ16 Φ3-Φ16 Φ3-Φ16 Φ3-Φ16
    Tapping diameter(mm) / 3-12 3-14 /
    Drilling depth(mm) 50 50 50 50
    Magnetic attraction(N) 13000 13000 13000 13000
    Speed(r/min) 810 0-700 0-810 500
    Trip(mm) 210 210 210 210
    Input 220-240V～ 50/60Hz(EUR/AUS) 120V～ 60Hz(US)
    Power(W) 1300 1300 1400 1550
    Fuse(A) 15
    Direction of rotation Forward Forward/ Reverse Forward/ Reverse Forward

    Description

    Vevor-8840-D8840-8850E-Magnetic-Drill-FIGURE-1

    The buttons on the control panel of some Vevor 8840-D8840-8850E Magnetic Drill machine models may be different. Please see the real product for detailed information.

    1. Rear cover
    2. Chassis
    3. Middle cover
    4. Gear box
    5. Electromagnet switch
    6. Handle
    7. Control Rod
    8. Forward/reverse switch
    9. Power switch
    10. Speed regulating knob
    11. Electromagnetic Base
    12. Track
    13. Seat belt sling hole

    Operation and Use

    Vevor-8840-D8840-8850E-Magnetic-Drill-FIGURE-2

    1. The drill bit must be sharp. When installing the hollow drill, insert the central needle into the hollow drill.
    2. Install the hollow drill on the output shaft, and finally, tighten the fixing screw to secure the hollow drill.
    3. The machine should be fastened with a Vevor 8840-D8840-8850E Magnetic Drill safety belt when working on the side or top.
    4. Thread one end of the safety belt into the handle hole of the frame, tie the other end to the strong frame, and then buckle it into the fasteners.
    5. Turn on the power switch to check whether the drill bit is beating and the sound is stable.
    6. If everything is normal, open the water valve first so that the cutting fluid in the oil can flow out, and then turn the handle to feed
    7. Feed should be slow at first. Do not exert too much in case of overload.
    8. If the motor suddenly stops or gets stuck due to a fault, the drill control switch must be turned off immediately.
    9. After continuous use for 2-3 hours, you need to rest to prevent the electromagnetic seat from burning out due to overheating.
    10. When the carbon brush is worn out, please replace it in time (both of them should be replaced at the same time).

    Adjustment of the Track

    Vevor-8840-D8840-8850E-Magnetic-Drill-FIGURE-3

    Fix B1 at B, then connect B2 to B1 and C

    Turn the joystick to determine whether Vevor 8840-D8840-8850E Magnetic Drill the tightness of the track meets the drilling requirements. If the tightness is not ideal, you can adjust it with the open wrench and the hex wrench in the attachment.

    Loosen the hex nut at place A with an open wrench. Use the hex wrench to adjust the set screw at A and turn the joystick simultaneously to feel whether the tightness of the track reaches the ideal state of drilling. After adjustment, tighten the hex nut at A with the open-end wrench.

    Maintainance & Storage

    1. After each use, clean the bottom of the magnetic seat drill and keep it properly.
    2. Please butter the track in time when the slide is not smooth.
    3. Please check the electrical protection device regularly.
    4. Whether grounding is reliable.
    5. Please check in on time during the rainy season.

    Troubleshooting

    Problem Reason SolutioThe magnetic holder
    er has no suction. Poor switch contact. Repair the switch.
    The power is off. Repairing the power
    The fuse is blown out. Replace the fuse
    An electromagnet can short-circuit or burn out. Repair or replace the magnetic base.
    It is not absorbed on steel parts. Change or thicken the adsorption surface. (thickness > 15mm).
    The machine won’t work after the power is on. Poor switch contact. Repair the switch.
    Loose plug. Connecting the power
    The brush does not contact the commutator. Replace the brush.
    Magnetic seat suction is weak. The adsorbed workpiece is too thin. Change or thicken the adsorption surface. (thickness > 15mm).
    Small adsorbable surface. Change the adsorption surface or temporarily weld the thick adsorption layer.r
    Elliptical holes appear in the drilling holes. The vibration caused the fastener to loosen. Tighten the fastener after correcting the verticality.
    The drill cuts only on one Regrinding bit.
    There is debris on the adsorption surface. Remove clutter.

    Component Comparison Table

    Vevor-8840-D8840-8850E-Magnetic-Drill-FIGURE-4

    No. Name No. Name No. Name
    1 Central needle 29 Coil spring 57 Bolt M6 x 6
    2 Rubber pad 30 Tapping screw ST2.9 x 9.5 58 Cylindrical pin x 10
    3 Elastic retaining ring 19 31 Brush holder component 59 Bolt M5x25
    4 Gasket 32 Nylon cable fixing head component 60 Electric magnet
    5 Spring plug 33 Hose 61 Spring gasket 6
    6 Spring 34 Bolt m4x6 62 Bolt M6 x 40
    7 Tapping screw ST4.8 x 40 35 Elbow cable retainer component 63 Connect wire 2
    8 Hexagon socket screw M8 x 8 36 Carbon brush 64 Connect wire 3
    9 Output axis 37 Oil can cover 65 Connect wire 1
    10 Bearing 6004 38 Oil can 66 Connect wire 4
    11 Seal ring 39 Bolt M4x10 67 gasket 4
    12 APC connector R1/8 40 Cable fixing plate 68 Electromagnetic switch
    13 Reduction gearbox 41 Nut M4 69 Swing plate switch
    14 Bearing 6003 42 Oil can retain a ring 70 Rod component
    15 4# gear 43 Water valve component G1/4 71 Rack shaft
    16 Bearing 608 44 Bolt M6 x 20 72 Switch fixing plate
    17 Flat key 4 x 4 x 6 45 Gasket 73 Circuit board
    18 3# gear shaft 46 Name plate 74 Bolt M5 x 16
    19 2# gear 47 Shaft ring 75 Nut M5
    20 Middle cover 48 Screw-pad combination M6x16 76 Base
    21 Bearing 6001 49 Rack 77 Screw cable fixing head
    22 Rotor 50 Bolt M5 x 20 78 Cable connector plug
    23 Bearing 608 51 Track regulating bar 79 PU hose
    24 Windshield ring 52 Track bar A 861 Safety Belt
    25 Tapping screw ST4 x 52 53 Guide rail plate 862 Open spanner 8mm
    26 Stator 54 Track bar B 863 Fuse
    27 Tapping screw ST4.2 x 25 55 Tapping screw ST2.9 x 9.5 864 Hexagonal open spanner 2.5mm
    28 Rear cover 56 Bolt M3 x 6 865 Hexagonal open spanner 4mm

    FCC Informaton

    This product is subject to the provisions of European Directive 2012/19/EC. The symbol showing a wheelie bin crossed through indicates that the product requires separate refuse collection in the European Union. This applies to the product and all accessories marked with this symbol.

    This device complies with Vevor EV-A01-US011B EV Charging Station with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

    1. This device may not cause harmful interference, and
    2. This device must accept any interference received, including interference that may cause undesired operation.RF Exposure：

    This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. Odyy.

    Radiation Exposure Statement

    This equipment complies with RSS-102 – Radio Frequency(RF)Exposure Compliance radiation exposure limits set forth for an uncontrolled environment.

    FCC Statements

    Digital device, under Part 15 of the FCC Rules. This equipment generates, usesandcanradiate radio frequency energy and, if not installedandusedinaccordance with the instructions, may cause harmful interference to communications. However, there is no guarantee that interference will not occur in a particular installation.

    • Reorient or relocate the receiving antenna.
    • Increase the separation between the equipment and receiver.
    • Consult the dealer or an experienced radiTV technician for help.

    Customer Service

    Share.

    Related Posts

    Add A Comment

    Comments are closed.