ADLER AD 7068 Steam Mop Adler 1300 W Instructions Guide

ADLER AD 7068 Steam Mop Adler 1300 W

Safety Instructions

1. Do not cover the appliance or cover its openings, as this may cause heat accumulation inside, which may lead to damage or fire.
2. Never leave the product connected to a power source unattended. Even if use is interrupted for a short time, unplug it from the mains and disconnect the power supply.
3. Never put the power cord, plug, or the entire device in water. Never expose the product to weather conditions such as direct sunlight or rain, etc.
4. Periodically check the condition of the power cord. If the power cord is damaged, return the product to a professional service center for replacement to avoid dangerous situations.
5. Never use the product near flammable materials.
6. Never point the outlet of the steam cleaner at yourself, other people, animals, or electrical appliances.
7. Only use the device with the original accessories.
8. Warning. Hot steam.
9. Warning. Hot steam can cause burns.
10. Do not touch the hot surfaces of the device.

Description

1. Handle
2. Cord holder
3. Metal tube
4. Power switch
5. Power cord
6. Water tank filler
7. Steam head joint
8. Parts of the machine(Graphic B page 2):A. Main body
   • B. Handle
   • C. Steam head
   • D. Micro fiber pad
   • E. Carpet cleaning pad
   • F. Measure

Before first use

1. Remove any packing material.
2. Wipe all components with a damp,p soft cloth.
3. Check the condition of the power cord. Prepare the device for operation:
4. Slide the handle (1) into the main body (A). (Graphic C page 3)
5. There is a bearing in the ADLER AD 7068 Steam Mop Adler 1300 W metal tube (3). It fits into the hole in the main body.
6. When installed correctly, the bearing will fall into the hole in the main body.
7. Connect the steam head (C) to the joint (7) as shown in the illustration, page E, 3.
8. To remove the metal tube, press down on the bearing and pull upward as shown in the page 3 illustration C.
9. Attach a microfiber pad to the steam head (C). To remove the pad, pull it firmly.
10. To refresh carpets, the carpet cleaning pad (E) should be applied to the previously attached microfiber pad as shown in illustration D, page 3.
11. Using the device:
12. Put on either a microfiber pad or a carpet cleaning pad, respectively.
13. After preparing the device for use. Plug the device into a power outlet.
14. Switch the switch to the on position.
15. The device will light up red until it heats up. This takes approximately 25 seconds, depending on the temperature of the room and water, it may be shorter or longer.
16. When you have finished working, turn off the device and let it cool down.
    Remove the microfiber pad.
17. Wash and dry the pads after each use to ensure hygienic cleanliness.
18. Pour out the remaining water from the tank.

Decalcification

Water container:

Depending on the hardness of the water in your home, the appliance should be descaled in the water container. To do this, add 2 tablespoons of white vinegar to the full water container and shake the appliance to distribute the solution throughout the water container. Set the device aside for several hours and empty the water container. Then rinse the entire container with clean water and leave the device to dry with the water container open.
Steam generating system: If you notice a drop in steam generation or no steam generation, you need to remove the scale from the steam generation system. For this purpose, in a measuring cup, create a

1. solution consisting of 1/3 white vinegar and 2/3 tap water.
2. Pour the solution into the water container and close the water container.
3. Put the device in a place resistant to acid, temperature, and water. E.g., sink, shower tray, bathtub. A microfiber pad is not needed to perform descaling.
4. Connect the device to electricity.
5. Turn on the device. The device will start producing steam.
6. Wait until the container empties.
7. The device still does not produce the previous amount of steam. Repeat the operation until the desired effect is achieved.
8. After successful descaling, rinse the container with clean water.
9. Fill the container with clean water and turn on the device until the steam generation empties the container.
10. The device is fully descaled.
11. After successful descaling, rinse the container with clean water.
12. Fill the container with clean water and turn on the device until the steam generation empties the container.

Troubleshooting

• Problem: No steam, low amount of steam:
• Possible cause: Empty water container.
• Solution: Add water.Possible cause: Blocked steam outlet.
• Solution: Clean the steam nozzle/decalcify.Possible cause: No power supply.
• Solution: Connect to the power supply.
• Possible cause: The device is not turned on.
• Solution: Turn on the device
• Problem: The device does not turn on.
• Possible cause: The device is not plugged in.
• Solution: Connect the device to the power supply.
  Possible cause: Burnt internal fuse. Solution: Contact central service.

Technical Data

• Power supply current: 220-240V~ 50Hz
• Power: 1300W
• Waterproof class: IPX4
• Capacity: 350ml

For the sake of the environment. Cardboard packaging and polyethylene (PE) bags should be disposed of in the appropriate containers for the separate collection of municipal waste according to their description. If there are batteries in the device, remove ADLER AD 7068 Steam Mop Adler 1300 W them and separately return them to the collection and storage facility.

They can also damage the kidneys, liver, and heart, and cause skin diseases. Harmful substances can also have adverse effects on the respiratory and reproductive systems and lead to cancerous changes. Consumption of plants growing on the contaminated soils, and products made from them, may risk the abovementioned health effects. Do not dispose of the device in the municipal waste container!!! If you wish to purchase spare parts or report any complaints, please contact the seller who issued the receipt directly.