Hubsan Zino Mini SE 3-Axis Gimbal Camera Drone
Safety Instructions
- Exercise extreme caution and responsibility when using the Drone.
- Small electronic components inside the Drone may be damaged due to shock or exposure to liquids.
- To avoid damage, do not operate the Drone with broken or damaged components.
- Do not disassemble, crush, impact, burn, drop, or step on the battery.
- Do not short or contact the battery terminal with metal.
- Do not expose the battery to temperatures above 60°C. Charge the Drone battery before flight.
- Please use a Hubsan dedicated charger for charging.
- Keep the battery out of the reach of children and away from any type of moisture.
Flight
Please be mindful of your personal safety and the safety of others when flying. Do not fly in adverse weather conditions. Do not attempt to grab the Drone while it is in flight. This product is intended for experienced riders over the age of 14. After each flight, disengage the motors and turn off the Drone, disconnect the battery, and then you can turn off the radio control.
Use Of Batteries
LiPo batteries are different from conventional batteries in that their chemical contents are enclosed in a particularly thin and light foil casing. This has the benefit of significantly reducing their weight but makes them more susceptible to damage if handled roughly and inappropriately. Like all batteries, there is a risk of fire or explosion if safety practices are ignored.
- Discharge the battery at a temperature no lower than 5°C.
- To avoid complete discharge and therefore damage the battery, do not prolong the discharge time.
- Do not disassemble or reassemble the battery.
- Do not short-circuit the battery.
- Do not use or charge near heat sources.
- Do not put the battery in contact with water or any type of liquid.
- Do not charge batteries in sunlight or near heat sources.
- Do not puncture or subject the battery to the force of any kind.
- Do not handle the battery improperly.
- Never charge a damaged, deformed, or swollen battery.
- Do not weld on or near the battery.
- Do not overcharge or excessively discharge the battery.
Drone
- Propeller A
- Propeller B
- Engine
- Foot (with antenna)
- Gimbal protection
- Drone body
- axis Gimbal
- Camera 4K HD
- Smart Battery
- Battery level indicator
- Power button
- USB Port
- Battery fixing clips
- TF card slot
- Sensors for altitude hold at low altitude
- Ground vision sensor VPU
- LED landing light for night flight
Aircraft Battery
Battery charging
The capacity of the lithium battery of the drone is 3000 mAh, for a voltage of 7.2 V. The standard version is supplied without a charger; therefore,, it is sufficient, to charge the battery with a phone charger with Micro USB adapter, the time of charging, a 2A charger, and about 2.5 hours. By purchasing the versions with bag or “combo”, a standard charger is supplied, the charg- ina timo l
Once, a series of LEDs will light up based on the battery charge.
- Connect the power supply to the AC mains (100V-240V, 50-60 Hz).
- Connect the switched-off smart battery to the charging adapter.
- The battery level indicator will flash and indicate the charge level
- Â The smart battery is fully charged when the power lights are all off.
- Disconnect the battery from the power supply after charging.
Battery Installation

- Have a 100% charged battery.
- Insert the battery into the compartment, press the clips on both sides of the battery until you hear the click.
- If the battery has been inserted correctly, it should be flush with the structure of the drone.
Precautions for low temperatures
- If the battery is used in a low temperature environment (-10°C to 5°C), please fully charge the battery and keep it warm before use.
- The battery cannot be used in an environment with a temperature lower than -10°C.
- Â In a low-temperature environment, it is recommended to immediately stop the flight when the APP communicates “Low battery alarm”.
- In a low-temperature environment, it is recommended to preheat the battery to 5°C or above before flight.
- In low temperature environments, the wind resistance of the Drone will be reduced due to the limitation of the battery output power. Please operate with caution.
- Â Before flying in a low-temperature environment, it is possible to insert the battery into the Drone after heating it for 1 or 2 minutes. Takeoff is possible after the battery has warmed up.
Battery precautions
Make sure to fully charge the battery each time before flying the Drone. The flight battery must use a dedicated Hubsan power adapter for charging.
- If the temperature of the intelligent flight battery is high at the end of the flight, it must be cooled to room temperature before charging.
The Propellers
Before installing the propeller, carefully check the letters next to the Drone’s motor and the letter engraved on the propeller. The two letters must match during installation. If the propeller blade is damaged, it must be replaced. Turn the screws counterclockwise to remove them.
Radio Control
Names of components of the radio control
- Smartphone support
- ) Forward/Backward – Left/Right
- RHT (Return to home)
- on and off button
- Speed button: F/N/S Film mod. – Normal mod. – Sport mod.
- Display
- Button for taking photos
- Button to record videos
- Gimbal adjustment|
- Â Programmable button
Radio Control Diagram
- Drone battery level
- Speed mode
- State of the propellers
- GPS satellites locked
- Drone control signal
- Radio control battery level
- Heading angle
- Information area
- Flight height
- Flight distance
Angle of the Radio Control antennas
- Adjust the angle of the antennas and direct them as much as possible towards the Drone. The distance between the two antennas is adequately narrow to maintain directivity for the long distance.
- The antennas are appropriately separated to maintain a wide range of action.
- Do not place obstacles and cross the antennas well.
Radio control calibration
- Pull both joysticks to the top left corner and simultaneously press and hold the power button to turn on
- Rotate both sticks to the maximum angle clockwise at least 3 times, then release the sticks.
- Long-press the button (except the power button) on the transmitter. When the remote control emits 3
- Â Turn off and restart the radio control.
Setting the radio control sticks
Open the menu from the App: Settings – Control – Stick Control Settings. The setting allows you to change the control mode (Mode 1 – Mode 2). Please remember that the default setting is MODE 2
Flight
Before flying, the user will need to download the X-Hubsan 2.0 Application. Download the Application for free by scanning the QR code shown on the side. Alternatively, download it via the App Store for IOS systems or with Google Play for ANDROID systems.
QR code to download the X-HUBSAN 2.0 App for Android
Pairing the Drone with the Radio Control
To use the aircraft for the first time, you need to activate the aircraft first :
- Press the battery switch to power on the aircraft. Press the remote control switch to connect to the mobile phone, and wait for the remote control to connect to the aircraft successfully.
- Open the mobile phone X-HUBSAN 2.0 APP, and it will automatically jump out of the activation interface. Activate according to the APP prompt.
Connection mode
Open and pull down the bracket of the remote control, take out the rocker from the rocker storage slot, and rotate and install the rocker in time. Unfold the antenna, put the mobile phone on the controller bracket, take out the connecting cable corresponding to the mobile phone (micro USB interface / type-C interface/lightning (iPhone) interface), and mark “TX” at one end of the connecting cable.
- Connect the remote control, and connect the mobile phone with “phone” on the other end. Short-press and then long-press to turn on the power supply of the remote control, and connect the remote control with the mobile phone through the cable.
- Open the x-hubsan 2.0 app, select the aircraft model, and click “enter the equipment”- Enter the aircraft operation interface. When the remote control icon changes to the repeater icon (Figure 2), it indicates that the remote control is connected to the mobile phone.
- Take out the aircraft, unfold the arm to the maximum angle, install the battery, and then remove the gimbal protective cover. Short-press once, then long-press the aircraft power supply, turn on the aircraft, close the aircraft to the remote control, and wait for 3 seconds. When the screen shows a real-
time transmission image, indicating that the aircraft has been successfully connected.
Drone Calibration
Horizontal calibration
During flight, the drone shows significant horizontal deviation, land and disarm the engines. Place the drone on a perfectly level horizontal surface. Open the setting interface in the APP, select horizontal calibration. The drone will automatically perform the calibration, and at the end, a message on the screen of the mobile device will inform you of the completion of this phase. Do not move or touch the Drone during calibration.
Compass calibration
When using the drone for the first time, the compass calibration before take-off message will be displayed. Follow the on-screen instructions, rotate the drone horizontally, then point the drone’s bow down towards the ground and rotate it clockwise. The compass calibration message will disappear once completed. Complete compass calibration before flying the drone for the first time.
Starting and stoppingÂ
The conditions for starting the engines must be the following:
- The Drone, the Radio Control, the Smartphone, or the Tablet must be connected;
- The Drone is calibrated with the compass (the App does not require calibration).
- The Drone must be positioned horizontally.
- The Drone has not locked onto sufficient GPS satellites useful for the flight. Do not force takeoff.
- The power of the drone should be =15%;
Starting/Stopping Engines
- Push both sticks into the bottom outer corners. With the engines running, release the sticks.
- Push both sticks into the bottom outer corners. With the engines stopped, release the sticks.
Forced Stop of The Engines
With the Drone in flight, it is possible to force the engines to stop by pushing both sticks in the lower external corners for at least 2 seconds.
Flight Control Mode
Return to Home (RTH)
There are three types of Return Home (R): RH with one button, R with low battery, and Riv for disconnection with the Radio Control. At take-off, the GPS must have locked more than 6 satellites (preferably 10), and the Drone marks the take-off point as the starting point.
Landing pad search
When the Drone is returning, and at a height of approximately 10 meters from the ground, it will automatically search for the Landing Pad to perform the landing.
REQUIREMENTS OF LANDING PAD
- Sharp contrast between the bottom and the writing on the Landing pad.
- The letter “H” character on the landing pad should be printed in white.
- The landing pad must be free of obstacles and possibly flat.
- Optical flow vision systems work well with adequate lighting and clearly visible or structured obstacles. The Drone is not designed to replace the pilot’s commands and assessments. Pay attention to the suggestions of the X-HUBSAN 2 APP.
- The best working range of the downward optical flow system is 0.5 to 5 meters. When this range is exceeded, positioning performance may decrease. Fly with caution.
- Always keep the vision sensors clean. Do not obstruct and/ or interfere with the detection system.
FLIGHT MODE
360 Shooting
Orbit Mode Flight
Click “Mode Selection”, then “Change Orbit” to set the current position or the center position of the mobile device. During Orbit mode, you can adjust the speed and direction of the Drone by moving the control stick left or right, and adjust the radius of the Orbit by moving the control stick forward or backward.
Rlight Waypoint Mode
The Drone will fly along a flight route created on the screen or a previously stored route. You can adjust the speed of the Drone during flight.
Line Fly Mode
- Click on “Mode Selection”, then on “Line Fly Mode” to set the angle, distance, and speed of the Drone.
- Enter “Follow” mode to choose tracking of a subject or the GPS of the remote control.
Image Tracking
Open Follow on the App. Select the subject to follow from track mode, click on “, Gand O” and the Drone will follow the subject’s movements. The altitude and distance detection range is 5 – 15 meters. This function cannot be performed if the distance between the drone and the subject is less than 5 meters. In follow me mode, the Drone will follow the control device  (Radio Control) when it is connected to the GPS.
Hyperlapse photography
By choosing the Time-lapse mod,e you can choose the “free” or “circular” mode.
15.10 Flight Panorama Mode
In panorama mode, you can choose 180° spherical, vertical, and wide-angle shooting. In this mode, the Drone automatically performs the shooting activity. Once shooting is complete, you can view photos and videos from the built-in MMC, export and edit photos and videos.
CAMERA
Camera Settings
Select the camera icon on the main interface of the App to set the resolution, white balance, color, and other parameters. Gimbal tilt adjustment
 Storing Images and Videos
Via an external TF U3 memory card, which,h depending on the model purchased, can have a capacity of 16 GB, 32 GB, 64 GB, or 128 GB. The system supports hot plugging, therefore it is possible to insert the TF Card even with the device turned on. It is preferable to insert or disconnect the TF Card with the drone turned off.
Home page and settings
- Home of the App, you can access various functions: Home, Photo and Video Editor, Tutorial, Service, Account, Hubsan Official Site, Flight Log, etc.
- Main interface where you can access all flight functions, camera settings, flight mode information, etc.
- Below are some of the easy-to-use App windows, the flight modes,
Waypoint Setting
General-purpose VERSION
General-purpose live streaming
VARIOUSÂ Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â Â WINDOWS
INCONVENIENCES
Causes and Remedies
- The Drone and the Radio Control do not connect.
- Check the App if the status of the control signal icon has changed.
- Adjust the radio control antenna, refer to the manual.
- Check the entry relating to USB connections in the Android tutorial.
- Â Disconnection between the radio control and the smartphone/tablet.
- The Drone is not detected.
- Stuck image transmission, unstable control signal, and frequent disconnection.
- The Drone flies unstably, tilts to the right or left, and does not respond normally to the radio control.
- The Drone’s GPS is not accurate and does not pass the accuracy test.
- Short flight autonomy.
- Overcharging the battery or high ambient temperature can easily lead to a reduction in battery life; we recommend maintaining the remaining 50% charge and fully recharging the batteries before use.
- Gimbal tilt angle is high, Gimbal shows abnormality, Gimbal does not
work, abnormal communication: Gimbal error code. - The pictures are not clear.
- Lens fogging.
- Not enough ambient light. Check whether the lens and the sensors of the optical positioning system installed on the bottom of the Drone are clean and free of foreign bodies.
POLICIES OF REFUND OR REPLACEMENT
Consumers of Hubsan products are entitled to additional warranties; these warranties do not limit or alter other consumer rights.
Our policy requires that the customer is always satisfied with our products. There are occasions when the customer may wish to exchange items. Within 7 days from the delivery date, Hubsan will accept all products for exchange. For a refund, Hubsan will accept all its products purchased on the Official Website. For details on refunding products purchased outside of the Hubsan Official Website, please contact a local authorized distributor.
To request a refund, repair, or replacement service, please contact Hubsan Aftersales Team. For further information, you will also be asked to fill out a mandatory support form.
REFUNDS SERVICE
- a) – Within 7 days of delivery, Hubsan will accept items in new, unaltered condition nd free of damage from the customer.
- b) – Within 7 days of delivery, Hubsan will accept items with obvious defects.
WARRANTY SERVICE
Consumers of Hubsan products are entitled to a warranty service; these guarantees do not limit or alter other consumer rights. These guarantees include your rights to our exchange, refund, and repair services. The warranty will provide free repair services, subject to the conditions described below
Conditions for a product to be eligible for the Hubsan warranty:
- The product has not been used inappropriately.
- The product was purchased completely new and sealed.
- The product has not undergone tampering or unauthorized modifications.
- Payment transaction receipt or proof of purchase must be provided.
- For repair or replacement of severely damaged products (under warranty), you must provide sufficient evidence that damage has occurred due to a defective component of a product.
Damage caused in these circumstances, the guarantee is not recognized:
- Unauthorized modification, disassembly, and/or improper installation of the product
- Operate under adverse natural forces (strong wind, rain, snow, storm, etc.)
- Operation under the interference of an electromagnetic source or environment.
- Failure to comply with the rules stated in the instruction manual.
- Any missing components or pieces are not covered by the warranty.
Warranty service information
Hubsan’s warranty service team will investigate and identify the problem. Once the product is received at our location, Hubsan will cover the cost of labor, materials, return, and shipping if the problem is found to be due to the quality of our product. If the product is found to be unsuitable for warranty service, the customer can choose to pay the
PAID REPAIR SERVICE
Hubsan also provides paid repair services for customers who do not meet the requirements for warranty, refund, or replacement services. For paid repair service, you will be charged for diagnostics, labor, materials,s and shipping costs. There will be no final costs until the product has been examined by our technicians.
CARE REFRESH ASSISTANCE SERVICE
The Care Refresh assistance service is available on the HUBSAN Official Website, which gives the possibility, by paying a sum indicated within the platform, to replace the Drone in the event of loss, collision,n or any other accident recognized by the Care Refresh formula.
Limitations of Liability
HUBSAN assumes no responsibility for damages, injuries,e s or legal liabilities arising directly or indirectly from the use of its products. Hubsan is not responsible for:
- Damage, injury, or any legal liability for user behaviour and in particular: state of intoxication, effect of narcotics, anesthesia, dizziness, fatigue, nausea, influenced by other physical or mental conditions that could compromise common sense or mental abilities.
- Incorrect subjective judgment or intentional malfunction of the products. Any mental, physical harm, impairment, illness, insurance claim, or accident involving Hubsan products. Use of the product in no-fly zones.
- Malfunctions or problems caused by modifications, disassembly and reassembly, replacement or use of accessories not authorized by Hubsan, failure to follow the instructions in the manual during installation and use.
- Damage, injury, or any legal liability caused by mechanical failure due to natural wear and tear (aircraft flight time over 100 hours), corrosion, hardware aging, etc. Continued flight after low voltage protection alarms are activated.
- Drones in flight with the awareness of anomalous conditions: if water, oil, earth, sand, or other unknown material is present inside the devices, the Drone or the radio components assembled incompletely, the main components have faults, etc., missing accessories, etc.
- Flying in situations or environments described below: areas with magnetic interference (such as high If the pilot loses sight of the Drone due to eye problems, it is not suitable for use with Hubsan products.s..
DECLARATION OF CONFORMITY
Hereby, SHENZHEN HUBSAN TECHNOLOGY CO. LTD, declares that this product complies with the essential requirements and other relevant provisions of the EU Directive 2014/53.
FCC INFORMATION
This equipment generates, uses, and can radiate radio-frequency energy, and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiv…
- Consult your local dealer or an experienced Radio/TV technician for assistance.
- This device complies with Part 15 of the FCC Rules.
Customer Support
Operation is subject to the following conditions. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
- Product name: Hubsan Mini
- Product standard number: Q/HBS 001-2017
- Producer: Shenzhen Hubsan Technology Co., Ltd
- Website: http://www.hubsan.com/
- Ph: +393458503209
- Address: Unit 2801-2802A, Building F, Xinghe WORLD Yabao Road, Bantian Street, Longgang District, Shenzhen, China