Close Menu
    Palmer

    Palmer ilm speaker simulation DI-box Instruction Guide

    By Updated:1 Comment4 Mins Read
    Palmer ilm speaker simulation DI-box

    Palmer-logo

    Palmer ILM speaker simulation DI-boxPalmer ilm speaker simulation DI-box

    Introduction

    The Palmer ILM Speaker Simulation DI-Box is designed to deliver clean, balanced audio signals, similar to other high-quality DI solutions like the Palmer KYLL 2-Kanal Line Isolation Box. It features 6.3 mm jack sockets on the input and output sides, which can be used both balanced and unbalanced. With high-quality transformer-based galvanic isolation, hum loops are reliably eliminated. This DI-box is perfect for balancing audio signals and transmitting them over long cable runs without interference.

    Safety Instructions

    1. Please read these instructions carefully before using the Palmer ILM Speaker Simulation DI-Box.
    2. Keep all information and instructions in a safe place.
    3. Follow the instructions.
    4. Use the device in the prescribed manner only.
    5. Do not open the device and do not perform any modifications.

    Packaging

    1. Packaging can be fed into the reusable material cycle using the usual disposal methods.
    2.  Please separate the packaging in accordance with disposal laws and recycling regulations in your country.
    Device
    1. This device is subject to the European Waste Electrical and Electronic Equipment Directive in the currently valid version.
    2. WEEE Waste Electrical and Electronic Equipment Directive. Old appliances do not belong in household waste.
    3. The old device must be disposed of via an approved disposal company or a municipal disposal facility.
    4. Please observe the applicable regulations in your country!
    5. Observe all disposal laws applicable in your country.
    6. As a private customer, you can obtain information on environmentally friendly disposal options from the seller of the product or the appropriate regional authorities.
    Batteries
    1. Observe all disposal laws applicable in your country.
    2. As a private customer, you can obtain information on environmentally friendly disposal options from the seller of the product or through the relevant regional authorities.
    The product is not suitable for
    • Persons (including children) with limited physical, sensory, or mental abilities or a lack of experience and knowledge.
    • Children (children must be instructed not to play with the device)

    Connections

    1. INPUT
      Line input with 6a.3 mm jack socket suitable for both unbalanced and balanced cabling. Use a shielded audio cable to connect, for example, a keyboard to the Line Isolation Box.
    2. OUTPUT
      Line output with a 6.3 mm jack socket suitable for both unbalanced and balanced cabling. Use a shielded audio cable to connect the Line Isolation Box to an input of a mixer or audio interface.

    For simpler setups, a single-channel alternative such as the Palmer Iller 1-Kanal Line Isolation Box can be used for balancing and transmitting audio signals over long cable runs.

    Palmer ilm speaker simulation DI-box

    Wiring Example

    -Palmer-Naab -Kanal-Media-DI-BoX-FG-2

    Technical Data

    Product number PWUPPER
    Product type Line Isolator
    No. of channels 1
    Type passive
    Transformer isolated yes
    No. of inputs 1
    Input type symmetrical/asymmetrical
    Input connections 6.3 mm jack
    No. of outputs 1
    Output type symmetrical/asymmetrical
    Output connections 6.3 mm jack
    Ground/lift switch no
    Housing Aluminium continuous casting
    Dimensions (H/W/D) 110 x 50 x 50 mm
    Weight 0.3 kg
    Ambient temperature for operation -20°C…70°C
    Relative air humidity <80%, non-condensing
    Included accessories

    AUDIO

    		 Rubber feet, inscription label
    Max. Input level (< 1% THD, 20 Hz) +10 dBu
    Max. Input level (< 1% THD, 1 kHz) +32 dBu
    Frequency response (±2dB, relative 1kHz) 20 Hz – 20 kHz
    Input impedance (1 kHz) 17 kΩ
    Output impedance (1 kHz) 500 Ω
    THD (30 Hz, +4 dBu, unity, unweighted) < 0.09 %
    THD (1 kHz, +4 dBu, unity, unweighted) < 0.002 %
    IMD (SMPTE) (60 Hz / 7 kHz, 4:1, +4 dBu) < 0.002 %
    Transformer ratio 1:1
    Manufacturer’s Declarations

    Herstellergarantie und Haftungsbeschränkung Manufacturer’s warranty & limitation of liability Adam Hall GmbH Adam-Hall-Str. 1 61627 Neu-Anspach, Germany.

    CE Conformity

    Adam Hall GmbH hereby confirms that this product, Palmer Pan16 19“ DI-bo,x meets the following guidelines (where applicable): Low-Voltage Directive (2014/35/EU), EMC Directive (2014/30/E/U), RoHS (2011/65/EU), RED (2014/53/EU)

    FCC Statement

    This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

    UKCA- Conformity

    Hereby, Adam Hall Ltd. declares that Palmer Naab 2-Kanal Media DI-Bo,x this product, Palmer Pan16 19“ DI-bo,x meets the following guidelines (where applicable): Electrical Equipment (Safety) Regulations 2016, Electromagnetic Compatibility Regulations 2016 (SI 2016/1091). The Restriction of the Use of Certain Palmer Pan16 19“ DI-box Hazardous Substances in Electrical and Electronic Equipment Regulation 2012 (SI 2012/),32,) Radio Equipment Regulations 2017 (SI 2016/2015), Adam Hall Ltd. | The Seedbed Bus. Centre | SS3 9QY Essex | UK

    Customer Support

    Share.

    Related Posts

    View 1 Comment